2007/12/03 The Exhaust Pipe Groups are Updated {1061} Caterpillar


The Exhaust Pipe Groups are Updated {1061}
`
2007/12/03 [SEPD0917]
AIR INLET AND EXHAUST SYSTEM
EXHAUST GP
2007/12/03 The Exhaust Pipe Groups are Updated {1061}
Off-Highway Truck:
797 (S/N: 5YW1-UP)
797B (S/N: JSM1-UP)

Description of Change: Two elbow assemblies have been updated in the exhaust pipe groups. The two elbow assemblies have updated flanges that now match the flanges that are on the muffler assemblies. The updated flanges will improve the clamping force of the clamps that are applied to the joints that are between the elbow assemblies and the mufflers. This will minimize exhaust leaks at the joints and the wear at the joints.

Adaptable To: The updated 174-6325 Elbow As and the updated 247-4178 Elbow As are now part of the 149-3079 Exhaust Pipe Gp. This is the arrangement for the standard machines. The new parts are adaptable back to the beginning of production of the machines.

The updated 253-6176 Elbow As and the updated 253-6177 Elbow As are now part of the 172-4336 Exhaust Pipe Gp. This is the high altitude arrangement for the machines. The new parts are adaptable back to the beginning of production of the machines.

Both sets of updated elbow assemblies became effective in production with the machine JSM306-UP. Use the following procedures in order to install the updated elbow assemblies onto earlier machines.

Installation of the Updated Elbow Assemblies on Standard Machines

Table 1
Parts Needed to Update the 149-3079 Exhaust Pipe Gp .    
Item     Qty     Part Number     Description    
1     1     247-4178     Elbow As    
2     1     174-6325     Elbow As    
3     2     7E-8452     Clamps    



    Illustration 1g01413299



    Illustration 2g01413304

  1. Remove the two 7E-8452 Clamps (6) from the 247-4178 Elbow As (4) and the 174-6325 Elbow As (5) .

  1. Remove the 188-1072 Clamp (11) from the 174-6325 Elbow As (5) .

  1. Remove the 233-7711 Heat Shield (8) from the 247-4178 Elbow As (4) .

  1. Remove the 241-8492 Band Clamp (15) from the 247-4178 Elbow As (4) .

  1. Remove the two 8T-4139 Bolts (13), the two 8T-4244 Nuts (14) and the four 5P-1076 Hard Washer (12) from the two elbow assemblies.

  1. Remove the six 8T-4192 Bolts (9), the six 8T-4223 Hard Washers (10) and the two 154-6351 Straps (7) from the elbow assemblies.

  1. With a suitable lifting device, remove the 247-4178 Elbow As (4) and the 174-6325 Elbow As (5) from the machine.

  1. Inspect the flange faces and the tubes on the end of the mufflers that are toward the elbow assemblies for damage. If you find damage to the flange faces or the tubes of the mufflers, replace the mufflers.

  1. By using a suitable lifting device, install the updated 174-6325 Elbow As (2). Secure the elbow assembly with the 188-1072 Clamp (11) that was removed in Step 2. Leave the clamp loose so you can adjust the parts. Install the new 7E-8452 Clamp (3) to the elbow assembly. Leave the clamp loose so you can adjust the parts.

  1. By using a suitable lifting device, install the updated 247-4178 Elbow As (1) to the bellows assembly. Secure the elbow assembly with the 241-8492 Band Clamp (15) that was removed in Step 4. Leave the clamp loose so you can adjust the parts. Install the new 7E-8452 Clamps (3) to the elbow assembly and the muffler assembly. Leave the clamp loose so you can adjust the parts.

  1. Install the two 8T-4139 Bolts (13), the two 8T-4244 Nuts (14) and the four 5P-1076 Hard Washers (12) that were removed in Step 5 to the two elbow assemblies.

  1. Install the six 8T-4192 Bolts (9), the six 8T-4223 Hard Washers (10) and the two 154-6351 Straps (7) that were removed in Step 4 to the bracket on the frame in order to secure the elbow assemblies.

  1. Tighten the 241-8492 Band Clamp (15) to 11 N·m (97 lb in).

  1. Tighten the two 7E-8452 Clamps (3) and the one 188-1072 Clamp (11) to 16 ± 4 N·m (12 ± 3 lb ft). Tap lightly around the circumference of the three clamps. Then, tighten the three clamps to 16 ± 4 N·m (12 ± 3 lb ft).

    Note: The static inspection torque should be no less than 9 N·m (80 lb in).

  1. Install the 233-7711 Heat Shield (8) that was removed in Step 3 to the updated 247-4178 Elbow As (1) .

Installation of the Updated Elbow Assemblies on Machines with the High Altitude Arrangement

Table 2
Parts Needed to Update the 172-4336 Exhaust Pipe Gp .    
Item     Qty     Part Number     Description    
1     1     253-6176     Elbow As    
2     1     253-6177     Elbow As    
3     2     7E-8452     Clamps    



Illustration 3g01413472



Illustration 4g01413474

  1. Remove the two 7E-8452 Clamps (6) from the 253-6176 Elbow As (4) and the 253-6177 Elbow As (5) .

  1. Remove the 233-7711 Heat Shield (10) and the 241-8492 Band Clamp (11) from the 253-6176 Elbow As (4) .

  1. Remove the 233-7711 Heat Shield (10) and the 241-8492 Band Clamp (11) from the 253-6177 Elbow As (5) .

  1. Remove the six 8T-4192 Bolts (8), the six 8T-4223 Hard Washers (9) and the two 154-6351 Straps (7) from the elbow assemblies.

  1. With a suitable lifting device, remove the 253-6176 Elbow As (4) and the 253-6177 Elbow As (5) from the machine.

  1. Inspect the flange faces and the tubes on the end of the mufflers that are toward the elbow assemblies for damage. If you find damage to the flange faces or the tubes of the mufflers, replace the mufflers.

  1. By using a suitable lifting device, install the updated 253-6176 Elbow As (1). Secure the elbow assembly with the 241-8492 Clamp (11) that was removed in Step 2. Leave the clamp loose so you can adjust the parts. Install one new 7E-8452 Clamp (3) to the elbow assembly and the muffler assembly. Leave the clamp loose so you can adjust the parts.

  1. By using a suitable lifting device, install the updated 253-6177 Elbow As (2) to the rear exhaust tube. Secure the elbow assembly with the 241-8492 Band Clamp that was removed in Step 3. Leave the clamp loose so you can adjust the parts. Install one new 7E-8452 Clamp (3) to the elbow assembly and the muffler assembly. Leave the clamp loose so you can adjust the parts.

  1. Tighten the 241-8492 Band Clamp (11) to 11 N·m (97 lb in).

  1. Tighten the two 7E-8452 Clamps (3) to 16 ± 4 N·m (12 ± 3 lb ft). Tap lightly around the circumference of the two clamps. Then, tighten the three clamps to 16 ± 4 N·m (12 ± 3 lb ft).

    Note: The static inspection torque should be no less than 9 N·m (80 lb in).

  1. Install the two 233-7711 Heat Shields (10) that were removed in Step 2 and Step 3 to the updated 253-6176 Elbow As (1) and to the 253-6177 Elbow As (2) .

Information System:

140M and 150 Motor Grader Piston Pump (All Wheel Drive) - Install
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Relief Valve (Line) - Test and Adjust
3500 Generator Sets Fuel System Secondary Filter - Replace
3176C Engine for the R1600G and the R1700G Load Haul Dumps Coolant Level - Test
3176C Engine for the R1600G and the R1700G Load Haul Dumps Cat Data Link - Test
140M and 150 Motor Grader Piston Pump (All Wheel Drive) - Remove
CP76 and CS76 Vibratory Compactors Propel System Pressure Override Valve (Axle Propel Pump) - Test and Adjust
CP76 and CS76 Vibratory Compactors Propel System Pressure Override Valve (Drum Propel Pump) - Test and Adjust
Parts Stock Cylinder Head Assemblies with Rust Preventative Applied{1100}
Multiple Registration Messages Occur with Product Link{733T, 7606}
561N Pipelayer Maintenance Interval Schedule
CP76 and CS76 Vibratory Compactors Propel System Piston Motor Flushing Valve (Axle) - Test and Replace
140M and 150 Motor Graders Engine Supplement Rear Chassis Support - Remove
2007/09/10 A New Lip Seal Is Now Used {3256, 3258, 3278, 7555}
140M and 150 Motor Grader Cab - Remove
140M and 150 Motor Grader Cab - Install
140M and 150 Motor Graders Engine Supplement Rear Chassis Support - Install
The Proper Procedures for Troubleshooting Mechanical Unit Injectors (MUI){1251, 1264, 1280, 1288, 1290}
IT38H Integrated Toolcarrier and 938H Wheel Loader Braking and Hydraulic Fan System Service Brake System Pressure - Test
Transportation Information {7000}
Correct Usage of the Oil Rail Plug for the Cylinder Head on C9 Engines{1100}
160M and 160 Motor Grader Power Train Front Axle - Remove
160M and 160 Motor Grader Machine Systems Fuel Tank - Remove
2007/09/24 The Body Exhaust Arrangement is Updated {1061, 1062}