Wheel Lean Bar - Remove and Install
`
14H Motor Grader Machine Systems
[RENR4193]
14H Motor Grader Machine Systems
Blade Lift Cylinder - Remove and Install
14H Motor Grader Machine Systems
Combination Valve - Remove
FRAME AND BODY
AXLE GP
14H Motor Grader Machine Systems
Wheel Lean Bar - Remove and Install
14H Motor Grader Machine Systems
Wheel Spindle - Remove
14H Motor Grader Machine Systems
Wheel Spindle - Install
14H Motor Grader Machine Systems
Front Axle - Remove
14H Motor Grader Machine Systems
Front Axle - Install
14H Motor Grader Machine Systems
Wheel Spindle and Wheel Spindle Housing - Remove
14H Motor Grader Machine Systems
Wheel Spindle and Wheel Spindle Housing - Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A(1) | 9U-7536 | Lift Stand | 1 |
| 447-0910 | Electric Hydraulic Pump Gp (115 V) | 1 | |
| 447-0911 | Electric Hydraulic Pump Gp (230 V) | 1 | |
| A1 | OR | ||
| 504-9791 | Lift Gp (60Hz)(2) | 1 | |
| 504-9793 | Lift Gp (50Hz)(3) | 1 | |
| B | 1P-1832 | Bearing Pulling Adapter | 1 |
| 4C-9633 | Puller Stud | 1 | |
| 350-7768 | Electric Hydraulic Pump Gp | 1 | |
| 6V-3160 | Double Acting Cylinder | 1 | |
| 5F-7353 | Washer | 1 | |
| 9U-6833 | Nut | 1 | |
Show/hide table
| (1) | Use Tooling (A) or (A1) based on requirements. |
| (2) | Operating Voltage (240 - 480V) |
| (3) | Operating Voltage (200 - 400V) |
- Use Tooling (A) to support front axle (1).
Show/hide table
Illustration 2 g06363496 For Tooling (A1). - Position Tooling (A1) as shown. Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (A1).
- Use Tooling (A1) to support front axle (1).
Show/hide table
Illustration 3 g01380749 Show/hide table
Illustration 4 g01380763 - Attach a suitable lifting device to both ends of wheel lean bar (2). The weight of wheel lean bar (2) is approximately
68 kg (150 lb) . - Remove bolt (3) and retainer (4).
- Repeat Step 5 for the opposite end of wheel lean bar (2).
- Remove wheel lean bar (2) from the wheel lean arms . Allow wheel lean bar (2) to rest on front frame (1).
- Remove the lifting device from the right side of wheel lean bar (2).
- Remove wheel lean bar (2).
Show/hide table
Illustration 5 g01380764 - Remove lip seals (5).
Show/hide table
Illustration 6 g06363056 - Use Tooling (B) to remove bearing (6). Repeat this step for the remaining bearing.
- Repeat Steps 10 and 11 for the opposite end of the wheel lean bar (2).
Show/hide table
| |
| Illustration 1 | g01346308 |
|
For Tooling (A). | |
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A(1) | 9U-7536 | Lift Stand | 1 |
| 447-0910 | Electric Hydraulic Pump Gp (115 V) | 1 | |
| 447-0911 | Electric Hydraulic Pump Gp (230 V) | 1 | |
| A1 | OR | ||
| 504-9791 | Lift Gp (60Hz)(2) | 1 | |
| 504-9793 | Lift Gp (50Hz)(3) | 1 | |
| B | 1P-1832 | Bearing Pulling Adapter | 1 |
| 4C-9633 | Puller Stud | 1 | |
| 350-7768 | Electric Hydraulic Pump Gp | 1 | |
| 6V-3160 | Double Acting Cylinder | 1 | |
| 5F-7353 | Washer | 1 | |
| 9U-6833 | Nut | 1 | |
| C | 1P-0510 | Driver Gp | 1 |
Show/hide table
| (1) | Use Tooling (A) or (A1) based on requirements. |
| (2) | Operating Voltage (240 - 480V) |
| (3) | Operating Voltage (200 - 400V) |
- Use Tooling (B) to install bearing (6). Repeat this step for the remaining bearing.
Show/hide table
Illustration 8 g01380764 - Use Tooling (C) to install lip seals (5). Repeat this step for the remaining lip seals.
Show/hide table
Illustration 9 g01380763 Show/hide table
Illustration 10 g01380749 - Attach a suitable lifting device to install wheel lean bar (2). The weight of wheel lean bar is approximately
68 kg (150 lb) . - Position wheel lean bar (2) on the machine. Allow wheel lean bar (2) to rest on front frame (1). Attach a second suitable lifting device on wheel lean bar (2).
- Install wheel lean bar (2) on the wheel lean arms.
- Install retainer (4) and bolt (3).
- Repeat Step 6 for the opposite end of wheel lean bar (2).
Show/hide table
Illustration 11 g06363496 For Tooling (A1). - Remove Tooling (A1) from front axle (1). Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (A1).
Show/hide table
Illustration 12 g01346308 For Tooling (A). - Remove Tooling (A) from front axle (1).
Show/hide table
| |
| Illustration 7 | g06363056 |
Information System:
Test Sequence for Capsule Type Fuel Nozzles{0782}
14H Motor Grader Machine Systems
Blade Lift Cylinder - Remove and Install
CB-634D Paving Compactor Machine Electronic Control System
Service Tools
574B Forwarder Power Train
On/Off Switches
D350E and D400E Articulated Trucks Power Train
Lockup Clutch and Solenoid Valve
574B Forwarder Power Train
Accelerator Pedal
3054E Industrial Engine
Camshaft Bearings - Remove and Install
793C and 793C XQ Off-Highway Truck Steering System
Steering Linkage and Cylinder Mounting
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks
ECM Output Circuit (Engine Coolant Temperature Lamp)
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks
ECM Output Circuit (Engine Oil Pressure Lamp)
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks
ECM Output Circuit (Engine ON Signal)
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers
MID 039 - CID 0975 - FMI 08
Bench Test Procedure for Hydraulic Piston Pumps{5070}
Bench Test Procedure for Hydraulic Piston Pumps {4268, 4306, 5070}
14H Motor Grader Machine Systems
Combination Valve - Remove
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System
Pump Control (Output Flow) - Adjust
14H Motor Grader Machine Systems
Bank Valve - Remove
14H Motor Grader Machine Systems
Bank Valve - Install
2002/10/28
Examine Failed Starting Motors to Understand the Reason for Failure {1453}
AP-655C and BG-2255C Asphalt Pavers Propel System
Pressure Limiter Valve - Test and Adjust
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System
Test/Enable Switch
574B Forwarder Power Train
Introduction
C15 Petroleum Generator Set Engines
Electric Starting Motor
3126B Machine Engines
5 Volt Engine Pressure Sensor Supply Circuit - Test