3054E Industrial Engine Camshaft Bearings - Remove and Install Caterpillar


Camshaft Bearings - Remove and Install
`
3054E Industrial Engine [RENR7569]
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
A  8S-2241  Camshaft Bearing Tool Group 
8H-0684 Ratchet Wrench 

Start By:

  1. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g00546333


    Illustration 2g00546238

  1. Use the Tooling (A) in order to remove the camshaft bearing (1) from the cylinder block.

Installation Procedure

Table 2
Required Tools 
Tool  Part Number  Part Description  Qty 
A  8S-2241  Camshaft Bearing Tool Group 
8H-0684 Ratchet Wrench 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 3g00546238


    Illustration 4g00546333

  1. Use the Tooling (A) in order to install the camshaft bearing (1) into the bore in the cylinder block.

    Note: Align the oil hole in camshaft bearing (1) with the oil hole in the bore in the cylinder block.

    Note: The camshaft bearing must be inserted until the front edge of the bearing is flush with the face of the recess in the cylinder block.

End By:

  1. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".

Information System:

793C and 793C XQ Off-Highway Truck Steering System Steering Linkage and Cylinder Mounting
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks ECM Output Circuit (Engine Coolant Temperature Lamp)
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks ECM Output Circuit (Engine Oil Pressure Lamp)
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks ECM Output Circuit (Engine ON Signal)
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0975 - FMI 08
574B Forwarder Power Train Monitoring System
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Piston Pump (Steering) - Disassemble
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Piston Pump (Steering) - Assemble
3054C Industrial Engine and C4.4 Marine Auxiliary Generator Set Fuel System Pressure - Test
3054C Industrial Engine and C4.4 Marine Auxiliary Generator Set Fuel System - Prime
3126B Machine Engines System Configuration Parameters
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Harvester Head System - Test
574B Forwarder Power Train Accelerator Pedal
D350E and D400E Articulated Trucks Power Train Lockup Clutch and Solenoid Valve
574B Forwarder Power Train On/Off Switches
CB-634D Paving Compactor Machine Electronic Control System Service Tools
14H Motor Grader Machine Systems Blade Lift Cylinder - Remove and Install
Test Sequence for Capsule Type Fuel Nozzles{0782}
14H Motor Grader Machine Systems Wheel Lean Bar - Remove and Install
Bench Test Procedure for Hydraulic Piston Pumps{5070}
Bench Test Procedure for Hydraulic Piston Pumps {4268, 4306, 5070}
14H Motor Grader Machine Systems Combination Valve - Remove
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Pump Control (Output Flow) - Adjust
14H Motor Grader Machine Systems Bank Valve - Remove