14H Motor Grader Machine Systems Solenoid Valve (Centershift Lock) - Remove and Install Caterpillar


Solenoid Valve (Centershift Lock) - Remove and Install
`
14H Motor Grader Machine Systems [RENR4193]
HYDRAULIC SYSTEM
CONTROL GP-CENTERSHIFT LOCK
14H Motor Grader Machine Systems Solenoid Valve (Centershift Lock) - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.

  1. Drain the air tanks. Refer to Operation and Maintenance Manual, "Air Tank Moisture and Sediment - Drain" for the correct procedure.


    Illustration 1g00931155

  2. Disconnect hose assemblies (2). Disconnect harness assemblies (4). Disconnect fitting (3). Remove bolts (1) and remove the solenoid valve.

Installation Procedure

Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.



    Illustration 2g00931155

  1. Install the solenoid valve and install bolts (1). Connect hose assemblies (2). Connect harness assemblies (4). Connect fitting (3).

Information System:

A Procedure for the Installation of the Product Link System is Available{7602, 7610, 7620}
AP-655C Asphalt Paver Shipping the Machine
14H Motor Grader Machine Systems Piston Pump (Hydraulic and Steering) - Install
14H Motor Grader Machine Systems Wheel - Remove and Install
AP-655C and BG-2255C Asphalt Pavers Propel System Relief Valve (Charge) - Test and Adjust
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Operational Checks
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0974 - FMI 02
3054E Industrial Engine Power Sources
C4.4 (Mech) Industrial Engine Engine Oil Cooler - Inspect
C4.4 (Mech) Industrial Engine Fuel Injection Nozzle - Test
3054E Industrial Engine Alternator - Test
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0973 - FMI 02
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Propel System Pump Control (Manual Displacement Control) Neutral - Test and Adjust
C4.4 (Mech) Industrial Engine Cylinder Head - Inspect
14H Motor Grader Machine Systems Tie Rod (Steering) - Remove and Install
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Harvester Head System - Test
3126B Machine Engines System Configuration Parameters
3054C Industrial Engine and C4.4 Marine Auxiliary Generator Set Fuel System - Prime
3054C Industrial Engine and C4.4 Marine Auxiliary Generator Set Fuel System Pressure - Test
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Piston Pump (Steering) - Assemble
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Piston Pump (Steering) - Disassemble
574B Forwarder Power Train Monitoring System
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0975 - FMI 08
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks ECM Output Circuit (Engine ON Signal)