3524B Engine for Caterpillar Built Machines Crankshaft Rear Seal and Wear Sleeve - Remove Caterpillar


Crankshaft Rear Seal and Wear Sleeve - Remove
`
1.1. Removal Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
1U-7600  Slide Hammer Puller 
1U-7325  Adapter 
5P-7409  Sleeve Distorter 

Start By:

  1. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove and Install".


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Every time that the crankshaft seal is removed from the wear sleeve, a new wear sleeve and crankshaft seal must be installed.




    Illustration 1g00659239

  1. Drill three evenly spaced holes and use Tooling (A) to remove seal (1) from the wear sleeve.


    Illustration 2g00659240

  2. Insert Tooling (B) between the rear housing and wear sleeve (2).


    NOTICE

    The use of excessive force on the sleeve distorter can cause the distorter adapter to crack the housing. To help avoid damage to the engine, do not use excessive force to remove the wear sleeve.


  3. Insert Tooling (C) between Tooling (B) and the wear sleeve. Carefully turn Tooling (C) until the edge of the tool causes a crease in the wear sleeve.

    Repeat this procedure several times around the wear sleeve until the wear sleeve can be removed by hand.

Information System:

797 Off-Highway Truck Power Train Transmission
RM-350B Road Reclaimer/Soil Stabilizer Machine Systems Rotor Drive Differential - Assemble
R2900 Load Haul Dump Machine Operation Information
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks Air Filter Restriction Lamp
3524B Engine for Caterpillar Built Machines Engine Oil Sequence Valves - Remove and Install
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Vibratory System Features
R2900 Load Haul Dump Transmission Control
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Piston Motor (Swing Drive) Relief Valve Pressure - Test and Adjust
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0154 - FMI 08
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0153 - FMI 08
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Braking System Brake System Air - Purge
14H and 16H Motor Graders Power Train Transmission and Transfer Gears
AP-655C and BG-2255C Asphalt Pavers Propel System Piston Pump Neutral - Test and Adjust
574B Forwarder Power Train Hydrostatic Drive System
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0168 - FMI 03
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0168 - FMI 04
CS-563E, CP-563E, CS-573E, CP-573E, CS-583E, CP-583E, CS-663E, CP-663E and CS-683E Vibratory Soil Compactors Drum Scrapers - Inspect/Adjust/Replace
120H and 135H Motor Graders Seat Belt
2002/11/18 Replacement Mobil-Trac System Belts Are Now Available for John Deere 8000T Series Agricultural Tractors {4198}
R2900 Load Haul Dump Stopping the Engine
CB-534D, CB-534D XW and CB-564D Paving Compactors Machine Systems Metering Pump (Steering)
14H Motor Grader Machine Systems Fuel Tank (Left Side) - Remove
14H Motor Grader Machine Systems Fuel Tank (Left Side) - Install
R2900 Load Haul Dump Lift Arm Positioner