C-15 and C-16 Industrial Engines Summary of Revisions Caterpillar


Summary of Revisions
`
C-15 and C-16 Industrial Engines [RENR2346]
BASIC ENGINE
C-15 and C-16 Industrial Engines Summary of Revisions
1.1. Information Changes

Information Changes

The following table summarizes the major changes in this manual:

Table 1
Titles     Description of Change    
Revision 01    
"Fuel Filter Base - Remove"     Tooling (A)    
"Fuel Filter Base - Install"     Tooling (A)    
"Electronic Unit Injector - Install"     Tooling (A)    
"Electronic Unit Injector Sleeve - Remove"     Tooling (A)    
"Electronic Unit Injector Sleeve - Install"     Tooling (B)
Tooling (D)    
"Turbocharger - Install"     Tooling (A)    
"Exhaust Manifold - Remove and Install"     Tooling (A) for Installation Procedure
Tooling (B) for Installation Procedure    
"Inlet and Exhaust Valve Seat Inserts - Remove and Install"     Tooling (A)    
"Engine Oil Filter Base - Remove"     Tooling (A)    
"Engine Oil Filter Base - Install"     Tooling (A)    
"Engine Oil Cooler - Disassemble"     Tooling (A)    
"Water Pump - Assemble"     Procedure
Tooling (D)    
"Flywheel - Remove"     Tooling (A)    
"Flywheel - Install"     Procedure
Tooling (A)
Tooling (B)    
"Crankshaft Rear Seal - Install"     Tooling (E)
Tooling (F)    
"Vibration Damper and Pulley - Remove and Install"     Tooling (A) for Installation Procedure    
"Crankshaft Front Seal - Install"     Tooling (E)
Tooling (F)    
"Gear Group (Front) - Install"     Tooling (A)
Tooling (B)    
"Valve Mechanism Cover Base - Remove and Install"     Tooling (A) for Installation Procedure    
"Cylinder Head - Install"     Tooling (A)
Tooling (B)
Tooling (C)    
"Camshaft - Install"     Tooling (F)
Tooling (G)    
"Camshaft Bearings - Remove"     Procedure    
"Camshaft Bearings - Install"     Procedure    
"Connecting Rod Bearings - Install"     Tooling (B)    
"Fan Drive - Assemble"     Tooling (B)    
"Electronic Control Module - Remove and Install"     Procedure    
"Alternator - Remove and Install"     Procedure    
"Electric Starting Motor - Remove and Install"     Procedure    
"Air Compressor - Remove and Install"     Tooling (A)    

Information System:

14H Motor Grader Operator Controls
14H Motor Grader Additional Messages
2002/11/11 A New Transmission Pressure Switch is now Used {3016, 3154}
14H and 16H Motor Graders Power Train Transmission Control Valve
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers Fuel Level Sender
C4.4 (Mech) Industrial Engine Lubrication System
2003/01/06 New Flash Software Is Now Used {7620}
3524B Engine for Caterpillar Built Machines Flywheel Housing - Install
574B Forwarder Power Train Differential
D5N Track-Type Tractor Transmission System Oil Sample - Obtain
2002/10/28 Changes to the Pump Drive Improve the Service Life {3016, 3108, 3154}
Product Link 151/201 Reporting Interval Erratic
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System System Pressure - Release
574B Forwarder Power Train Gearshift Valve
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Hydraulic Oil Contamination - Test
R2900 Load Haul Dump Tilt Cylinder and Tilt Lever Bearings - Lubricate
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Hydraulic System Air - Purge
14H and 16H Motor Graders Power Train Differential and Bevel Gear
R2900 Load Haul Dump Transmission Oil - Change
R2900 Load Haul Dump Transmission Oil Filter - Replace
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0070 - FMI 02
3054E Industrial Engine Electrical System
CS-563E, CP-563E, CS-573E, CP-573E, CS-583E, CP-583E, CS-663E, CP-663E and CS-683E Vibratory Soil Compactors Gauges
14H Motor Grader Machine Systems Piston Pump (Fan Drive) - Remove