14H Motor Grader Machine Systems Centershift Lock - Install Caterpillar


Centershift Lock - Install
`
1.1. Installation Procedure

Installation Procedure

Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.



    Illustration 1g00928861

  1. Install seals (18) and back up rings (19) in housing (17).


    Illustration 2g00928838

  2. Install O-ring seal (11), piston (12), seals (13), plate (14), lock (15), and bolts (16) on pin (9). Bend lock (15) against bolts (16).


    Illustration 3g00929682

  3. Install pin (9) in housing (10). Position housing (10) on centershift lock (8).


    Illustration 4g00929677

    ------ WARNING! ------

    Personal injury can result from being struck by parts propelled by a released spring force.

    Make sure to wear all necessary protective equipment.

    Follow the recommended procedure and use all recommended tooling to release the spring force.


  4. Install spring (5), washers (6), and O-ring seal (7).

  5. Install housing (1). Install bolts (2) that hold housing (1).

    Note: Bolts (2) must be installed evenly.



    Illustration 5g00928777

  6. Connect hose assemblies (3).

Information System:

14H Motor Grader Machine Systems Centershift Lock - Remove
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Machine Preparation for Troubleshooting
D5N Track-Type Tractor Seat
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Braking System Accumulator Charging Valve (Brake)
IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader Hydraulic System
R2900 Load Haul Dump Service Inspection
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0248 - FMI 02
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Braking System Vane Pump (Braking)
3524B Engine for Caterpillar Built Machines Flywheel - Remove and Install
3054E Industrial Engine Fuel System Pressure - Test
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Braking System General Information (Braking)
3516B and 3516C Engines for Off-Highway Trucks Lubrication System
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0263 - FMI 03
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0263 - FMI 04
R2900 Load Haul Dump Autoshift Control (STIC Steering)
R2900 Load Haul Dump Autoshift Control (Wheel Steering)
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0271 - FMI 05
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0271 - FMI 06
574B Forwarder Power Train Braking System
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0324 - FMI 05
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0324 - FMI 06
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Parking Brake (Travel)
Product Link 151/201 Reference Parts Information
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Summary of Revisions