14H Motor Grader Machine Systems Swivel - Remove Caterpillar


Swivel - Remove
`
1.1. Removal Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
138-7575  Link Bracket 
ZZ  6V-9509  Face Seal Plug 
6V-9508 Face Seal Plug 
6V-9830 Cap As 
6V-9829 Cap As 

Start By:

  1. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Machine Preparation for Disassembly and Assembly".

Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.

Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.


------ WARNING! ------

Personal injury can result from hydraulic oil pressure and hot oil.

Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.

Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.


Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.

  1. Drain any hydraulic oil into a suitable container for storage or disposal.


    Illustration 1g00928380

  2. Disconnect hose assemblies (1) and (2).


    Illustration 2g00928384

  3. Remove cotter pin (3). Remove pin (4). Lower bracket (5).


    Illustration 3g00928387

  4. Disconnect four hose assemblies (6).

  5. Attach Tooling (A) to swivel (7). attach a suitable lifting device to Tooling (A). The weight of swivel (7) is approximately 39 kg (85 lb).

  6. Remove bolts (8). Remove swivel (7).

Information System:

938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Hydraulic System Pilot Valve
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Hydraulic System Piston and Vane Pump (Implement Section)
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Hydraulic System Electrical Output Components
R2900 Load Haul Dump Implement and Steering Lockout (STIC Steering) - Test
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers Diagnostic Code List
3176C and 3196 Engines for Caterpillar Built Machines Replacing the ECM
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Machine Systems Gear Motor (Fan Drive)
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Machine Systems Metering Pump (Steering)
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Propel System Piston Motor (Drum Propel)
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks Diagnostic Codes
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Machine Systems Gear Pump (Steering)
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1738 - FMI 06
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Hydraulic System Relief Valve (Main)
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Hydraulic System Relief Valve (Line)
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Hydraulic System Ride Control System
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Hydraulic System Gear Motor (Hydraulic Fan)
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Vibratory System Support and Vibratory Drive
14H Motor Grader Machine Systems Swivel - Install
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Vibratory System Piston Motor (Vibratory System)
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Vibratory System Piston Pump (Vibratory System)
D350E and D400E Articulated Trucks Power Train Front Axle
120H and 135H Motor Graders Machine Systems Swivel - Disassemble
120H and 135H Motor Graders Machine Systems Swivel - Assemble
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Vibratory System Bypass Valve (Return Manifold)