140M and 150 Motor Grader Piston Pump (Hydraulic Fan) - Remove Caterpillar


Piston Pump (Hydraulic Fan) - Remove
`
1.1. Removal Procedure

Removal Procedure

Start By:

  1. Remove the bottom guard. Refer to Disassembly and Assembly, "Bottom Guard - Remove".

------ WARNING! ------

Personal injury can result from hydraulic oil pressure and hot oil.

Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.

Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.



NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


Note: Put identification marks on all hoses, on all hose assemblies, on all harness assemblies, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.

  1. Connect the steering frame lock. Refer to Operation and Maintenance Manual, "Steering Frame Lock".

  2. Drain the hydraulic system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Capacities - Refill" for the capacity of the hydraulic tank. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change".


    Illustration 1g01382147

  3. Disconnect hose assemblies (1) and (4). Disconnect tube assembly (3).

  4. Remove bolts (2) in order to remove piston pump (5) from the machine. The weight of piston pump (5) is approximately 18 kg (40 lb).

Information System:

CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Motor (Drum Propel)
Field Installation of the Traction Control System for the 770, and 772 Off-Highway Trucks{1408, 3288, 4257, 4294, 4801, 4811, 5057, 7610, 7620, 7960}
140M and 150 Motor Grader Secondary Steering Pump and Motor - Install
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Pump (Propel)
120M and 12M Motor Grader Machine Systems Articulation Cylinder - Remove and Install - Left Side
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Hydraulic Oil Filter (Charge)
C32 Engine for D11T Track-Type Tractors Cooling Fan Control - Test
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Hydraulic Tank
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Propel System Components
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Operator Controls (Propel System)
C32 Engine for D11T Track-Type Tractors Coolant Flow - Test
120M and 12M Motor Grader Machine Systems Blade Lift Arm - Install
CP54 and CS54 Vibratory Soil Compactors Machine Systems Relief Valve (Main, Vibratory) - Test and Adjust
2570C and 2670C Wheel Feller Bunchers Engine Air Filter Secondary Element - Replace
770 and 772 Off-Highway Trucks Power Train Final Drive - Remove
770 and 772 Off-Highway Trucks Power Train Final Drive - Install
770 and 772 Off-Highway Trucks Power Train Final Drive - Disassemble
770 and 772 Off-Highway Trucks Power Train Final Drive - Assemble
CB22, CB24, CB32 and CC24 Utility Compactors Braking System - Test
CB22, CB24, CB32 and CC24 Utility Compactors Cooling System Coolant (ELC) - Change
CB22, CB24, CB32 and CC24 Utility Compactors Cooling System Coolant Extender (ELC) - Add
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Motor (Wheel Propel)
CB22, CB24, CB32 and CC24 Utility Compactors Cooling System Water Temperature Regulator - Replace
Repair of Cracks in Front Frame Crossmember{7051}