140M and 150 Motor Grader Window Wiper and Wiper Motor (Door) - Remove and Install - Side Caterpillar


Window Wiper and Wiper Motor (Door) - Remove and Install - Side
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure



    Illustration 1g01359119

  1. Remove nut (1). Disconnect hose (2). Remove window wiper (3).

    Note: Mark the position of window wiper (3) for installation purposes.



    Illustration 2g01359134

  2. Remove cap (4).


    Illustration 3g01359139

  3. Remove cover (5).


    Illustration 4g01415056

  4. Disconnect harness assembly (6).


    Illustration 5g01415061

  5. Remove panel assembly (7).


    Illustration 6g01415064

  6. Disconnect harness assembly (8).


    Illustration 7g01415203

  7. Remove nut (9).


    Illustration 8g01415212

  8. Remove nuts (10) to remove wiper motor (11).

  9. Repeat Steps 1 through 8 for the remaining window wiper and wiper motor assembly.

Installation Procedure



    Illustration 9g01415212

  1. Install wiper motor (11). Install nuts (10). Tighten nuts (10) to a torque of 7.5 ± 0.5 N·m (66 ± 4 lb in).


    Illustration 10g01415203

  2. Install nut (9). Tighten nut (9) to a torque of 9 ± 1 N·m (79.65675 ± 8.85075 lb in).


    Illustration 11g01415064

  3. Connect harness assembly (8).


    Illustration 12g01415061

  4. Install panel assembly (7).


    Illustration 13g01415056

  5. Connect harness assembly (6).


    Illustration 14g01359139

  6. Install cover (5).


    Illustration 15g01359134

  7. Install cap (4).


    Illustration 16g01359119

  8. Install window wiper (3). Connect hose (2). Install nut (1). Tighten nut (1) to a torque of 21 ± 1 N·m (186 ± 9 lb in). After approximately 30 minutes, tighten nut (1) again to a torque of 21 ± 1 N·m (186 ± 9 lb in).

    Note: When checking the torque of nut (1) in the field, nut (1) must have a minimum torque of 12 N·m (106 lb in).

  9. Repeat Steps 1 through 8 for the remaining window wiper and wiper motor assembly.

Information System:

Installation of the Power Shift Solenoid{5264, 5479}
C32 Engine for D11T Track-Type Tractors Coolant Temperature Is High
CB34, CB34XW and CC34 Utility Compactors Fuel System Water Separator Element - Replace
CB34, CB34XW and CC34 Utility Compactors Plate Locations and Film Locations
CB34, CB34XW and CC34 Utility Compactors Capacities (Refill)
CB34, CB34XW and CC34 Utility Compactors Sound Information and Vibration Information
CB22, CB24, CB32 and CC24 Utility Compactors Capacities (Refill)
140M and 150 Motor Grader Blade Lift Cylinder - Remove and Install
140M and 150 Motor Grader Wheel Lean Bar - Remove and Install
AccuGrade GPS (CD700) Design Surface Type
AccuGrade GPS (CD700) Plan View
AccuGrade GPS (CD700) Sloping Surface Design
CP54 and CS54 Vibratory Soil Compactors Machine Systems System Pressure - Release
C32 Engine for D11T Track-Type Tractors Fuel Filter Is Restricted
C32 Engine for D11T Track-Type Tractors Fuel Temperature Is High
C27 and C32 Engines for Caterpillar Built Machines Exhaust Temperature Is High
C32 Engine for D11T Track-Type Tractors Inlet Air Temperature Is High
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Vibratory Frequency - Test and Adjust - Fixed
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Magnetic Sensor (Vibratory) - Test and Adjust
CP54 and CS54 Vibratory Soil Compactors Machine Systems Hydraulic Oil Contamination - Test
140M and 150 Motor Grader Power Train Gear Pump (Transmission Charging and Scavenge) - Remove
140M and 150 Motor Grader Power Train Gear Pump (Transmission Charging and Scavenge) - Install
VIMS Communicator Troubleshooting
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Case Drain Flow for Piston Motor (Vibratory) - Test