140M and 150 Motor Graders Engine Supplement Engine Oil Filter and Base - Remove and Install Caterpillar


Engine Oil Filter and Base - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
185-3630  Strap Wrench As 

Note: Plug and cap all open ports and tube assemblies.


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on AVSpare products.

Dispose of all fluids according to local regulations and mandates.


------ WARNING! ------

Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.


------ WARNING! ------

Personal injury can result from contact with refrigerant.

Contact with refrigerant can cause frost bite. Keep face and hands away to help prevent injury.

Protective goggles must always be worn when refrigerant lines are opened, even if the gauges indicate the system is empty of refrigerant.

Always use precaution when a fitting is removed. Slowly loosen the fitting. If the system is still under pressure, release it slowly in a well ventilated area.

Personal injury or death can result from inhaling refrigerant through a lit cigarette.

Inhaling air conditioner refrigerant gas through a lit cigarette or other smoking method or inhaling fumes released from a flame contacting air conditioner refrigerant gas, can cause bodily harm or death.

Do not smoke when servicing air conditioners or wherever refrigerant gas may be present.

Use a certified recovery and recycling cart to properly remove the refrigerant from the air conditioning system.


  1. Recover the air conditioner refrigerant from the air conditioner system. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the correct charge that is used in the machine that is being serviced. Refer to Service Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for the procedure. Refer to Special Publication, NENG2500, "Air Conditioning Tools" for the tools.

  2. Drain the coolant into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".

  3. Drain the oil into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Oil - Change".


    Illustration 1g01414460

  4. Remove bolts (1). Move ball valve (2) to the CLOSED position. Loosen bolt (3).


    Illustration 2g01414513

  5. Remove bolt (5). Remove bracket assembly (4).


    Illustration 3g01414519

  6. Remove tube assembly (6). Disconnect tube assembly (7) and reposition. Use Tooling (A) in order to remove filter assembly (11). Remove bolts (8). Remove engine oil filter base and cooler (10).

Installation Procedure



    Illustration 4g01414519

  1. Install engine oil filter base and cooler (10). Install bolts (8). Install filter assembly (11). Position tube assembly (7). Connect tube assembly (11). Install tube assembly (6).


    Illustration 5g01414513

  2. Install bracket (4). Install bolt (5).


    Illustration 6g01414460

  3. Tighten bolt (3). Move ball valve (2) to the OPEN position. Install bolts (1).

  4. Fill the machine with oil. Refer to Operation and Maintenance Manual, "Oil - Change".

  5. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".

  6. Charge the air conditioner system. Refer to Service Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for the correct procedure. Refer to Special Publication, NENG2500, "Air Conditioning Tools" for the correct tools.

Information System:

CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Case Drain Flow for Piston Motor (Axle Propel) - Test
CB22, CB24, CB32 and CC24 Utility Compactors Rollover Protective Structure (ROPS) - Foldable
PL1000E Communication ECM Modbus Master
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Case Drain Flow for Piston Motor (Drum Propel) - Test
279C, 289C and 299C Compact Track Loaders Reference Material
The Electronic Priming Pump for Machine Engines will not Prime{1258, 1263}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Piston Ring Groove - Inspect
2007/10/08 A New Main Power Relay and Starter Relay are Now Used {4493, 7499}
2007/10/08 A New Main Power Relay, Starter Relay and Glow Plug Relay are Now Used {1403, 1412, 4493, 7499}
Replacement of the Blower Assembly on Certain Wheel Loaders{7304, 7320}
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Neutral Start Switch - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Axle Propel) - Test and Adjust
CB22, CB24, CB32 and CC24 Utility Compactors Shipping the Machine
VIMS Communicator Toolkit Poll Parameters
VIMS Communicator Toolkit Program Description
VIMS Communicator Toolkit Setup
VIMS Communicator Toolkit System Requirements
VIMS Communicator Toolkit Troubleshooting
160M and 160 Motor Grader Machine Systems Control Valve (Brake) - Remove
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Travel Speed - Check
160M and 160 Motor Grader Machine Systems Control Valve (Brake) - Install
VIMS Communicator General Information
14L Motor Grader Machine Systems Control Valve (Brake) - Disassemble
14L Motor Grader Machine Systems Control Valve (Brake) - Assemble