140M and 150 Motor Grader Control Manifold (Steering Backup) - Install Caterpillar


Control Manifold (Steering Backup) - Install
`
1.1. Installation Procedure

Installation Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
311-1362  Vacuum Gauge Gp 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g01404536

  1. Position control manifold (6) and install bolts (3).

  2. Connect tube assemblies (5).

  3. Connect harness assemblies (4).


    Illustration 2g01413659

  4. Position cover (2).

  5. Install bolts (1). Repeat this step for the opposite side of the machine.


    Illustration 3g01397769

  6. Remove Tooling (A).

End By:

  1. Disconnect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".

  2. Test the steering backup control manifold. Refer to Testing and Adjusting, "Control Manifold (Steering Backup) - Test".

Information System:

140M and 150 Motor Grader Control Manifold (Steering Backup) - Remove
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Pump Neutral (Drum Propel Pump) - Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pressure Override Valve (Axle Propel Pump) - Test and Adjust
140M and 150 Motor Grader Steering Control Valve - Install
140M and 150 Motor Graders Engine Supplement Radiator Guard and Support, Aftercooler, Hydraulic Oil Cooler, and Radiator, - Install
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pressure Override Valve (Drum Propel Pump) - Test and Adjust
R1600G Load Haul Dump Machine Electrical System Actual Gear Indicator
R1600G Load Haul Dump Machine Electrical System Engine Stop
R1600G Load Haul Dump Machine Electrical System Engine Start
R1600G Load Haul Dump Machine Electrical System Engine Start (Remote Control)
R1600G Load Haul Dump Machine Electrical System Autoshift Control (STIC Steering)
R1600G Load Haul Dump Machine Electrical System Heating and Air Conditioning
CB22, CB24, CB32 and CC24 Utility Compactors Safety Messages
CB22, CB24, CB32 and CC24 Utility Compactors Sound Information and Vibration Information
CB22, CB24, CB32 and CC24 Utility Compactors Specifications
CB22, CB24, CB32 and CC24 Utility Compactors Plate Locations and Film Locations
Air Conditioning and Heating R134a for All Caterpillar Machines Refrigerant Compressor
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Pump Neutral (Axle Propel Pump) - Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Drum Propel) - Test and Adjust
2007/10/01 A New Transmission Speed Sensor is Now Available for Series H-Series Motor Graders {3175}
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Axle Propel) - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Neutral Start Switch - Test and Adjust
Replacement of the Blower Assembly on Certain Wheel Loaders{7304, 7320}
2007/10/08 A New Main Power Relay, Starter Relay and Glow Plug Relay are Now Used {1403, 1412, 4493, 7499}