140M and 150 Motor Grader Control Manifold (Steering Backup) - Remove Caterpillar


Control Manifold (Steering Backup) - Remove
`
1.1. Removal Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
311-1362  Vacuum Gauge Gp 

Start By:

  1. Release the system pressure. Refer to Disassembly and Assembly, "System Pressure - Release".

  2. Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.


------ WARNING! ------

Personal injury can result from hydraulic oil pressure and hot oil.

Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.

Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.



NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


Note: Put identification marks on all harness assemblies, and on all tube assemblies for installation purposes. Plug all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.



    Illustration 1g01397769

  1. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A). Apply 138 kPa (20 psi). This procedure will pull a vacuum on the hydraulic system.


    Illustration 2g01413659

  2. Remove bolts (1). Repeat this step for the opposite side of the machine.

  3. Remove cover (2).


    Illustration 3g01404536

  4. Disconnect harness assemblies (4).

  5. Disconnect tube assemblies (5).

  6. Remove bolts (3) and remove control manifold (6).

Information System:

CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Pump Neutral (Drum Propel Pump) - Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pressure Override Valve (Axle Propel Pump) - Test and Adjust
140M and 150 Motor Grader Steering Control Valve - Install
140M and 150 Motor Graders Engine Supplement Radiator Guard and Support, Aftercooler, Hydraulic Oil Cooler, and Radiator, - Install
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pressure Override Valve (Drum Propel Pump) - Test and Adjust
R1600G Load Haul Dump Machine Electrical System Actual Gear Indicator
R1600G Load Haul Dump Machine Electrical System Engine Stop
R1600G Load Haul Dump Machine Electrical System Engine Start
R1600G Load Haul Dump Machine Electrical System Engine Start (Remote Control)
R1600G Load Haul Dump Machine Electrical System Autoshift Control (STIC Steering)
R1600G Load Haul Dump Machine Electrical System Heating and Air Conditioning
R1600G Load Haul Dump Machine Electrical System Main Power Relay
140M and 150 Motor Grader Control Manifold (Steering Backup) - Install
CB22, CB24, CB32 and CC24 Utility Compactors Safety Messages
CB22, CB24, CB32 and CC24 Utility Compactors Sound Information and Vibration Information
CB22, CB24, CB32 and CC24 Utility Compactors Specifications
CB22, CB24, CB32 and CC24 Utility Compactors Plate Locations and Film Locations
Air Conditioning and Heating R134a for All Caterpillar Machines Refrigerant Compressor
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Pump Neutral (Axle Propel Pump) - Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Drum Propel) - Test and Adjust
2007/10/01 A New Transmission Speed Sensor is Now Available for Series H-Series Motor Graders {3175}
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Axle Propel) - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Neutral Start Switch - Test and Adjust
Replacement of the Blower Assembly on Certain Wheel Loaders{7304, 7320}