140M and 150 Motor Graders Engine Supplement Engine Support (Front) - Remove and Install Caterpillar


Engine Support (Front) - Remove and Install
`
140M and 150 Motor Graders Engine Supplement [KENR6423]
BASIC ENGINE
MOUNTING GP-ENGINE
140M and 150 Motor Graders Engine Supplement Engine Support (Front) - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Start By:

  1. Remove the engine enclosure. Refer to Disassembly and Assembly, "Engine Enclosure - Remove ".


    Illustration 1g01412929

  1. Attach a suitable lifting device onto the front engine bracket (1).


    Illustration 2g01412930

  2. Remove bolt (2).

  3. Repeat Step 2 for the other side.

  4. Use a suitable lifting device in order to raise the front of the engine. The weight of the engine is approximately 1065 kg (2350 lb).

  5. Remove engine supports (front) (3).

Installation Procedure



    Illustration 3g01412929

  1. Attach a suitable lifting device onto the front engine bracket (1).

  2. Use a suitable lifting device in order to raise the front of the engine. The weight of the engine is approximately 1065 kg (2350 lb).


    Illustration 4g01412930

  3. Install engine supports (front) (3).

  4. Install bolt (2).

  5. Repeat Steps 3 and 4 for the other side.

End By:

  1. Install the engine enclosure. Refer to Disassembly and Assembly, "Engine Enclosure - Install".

Information System:

770 and 772 Off-Highway Trucks Power Train Differential and Bevel Gear - Install
770 and 772 Off-Highway Trucks Power Train Differential and Bevel Gear - Disassemble
770 and 772 Off-Highway Trucks Power Train Differential and Bevel Gear - Remove
140M and 150 Motor Grader Power Train Gear Pump (Transmission Charging and Scavenge) - Assemble
2007/11/26 New Pressure Switches Update the Wiring Groups and Lines Groups {1408, 4304}
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Relief Valve (Main, Drum Propel Pump) - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Relief Valve (Charge Pressure, Axle Propel Pump) - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Relief Valve (Charge Pressure, Drum Propel Pump) - Test and Adjust
140M and 150 Motor Grader Power Train Gear Pump (Transmission Charging and Scavenge) - Disassemble
2007/10/08 A New Main Power Relay and Starter Relay are Now Used {4493, 7499}
CB34, CB34XW and CC34 Utility Compactors Battery Disconnect Switch - If Equipped
160M and 160 Motor Grader Power Train Transmission Oil Cooler - Install
2008/01/28 The Lighting Wiring Group is Updated {1408, 1429, 7553}
C32 Engine for D11T Track-Type Tractors Component Location
140M and 150 Motor Grader Piston Pump (Hydraulic Fan) - Disassemble
160M and 160 Motor Grader Power Train Front Axle - Install
140M and 150 Motor Grader Piston Pump (Hydraulic Fan) - Assemble
3500 Generator Sets Air Shutoff - Test - Engines That Are Equipped with ADEM II or ADEM III Engine Control Modules (If equipped)
C32 LRC Engine for Track-Type Tractors Electrical Connectors
CB34, CB34XW and CC34 Utility Compactors Lifting and Tying Down the Machine
CB34, CB34XW and CC34 Utility Compactors Towing the Machine
2008/12/15 The Control Assembly is Updated in the Cab {7304, 7320, 7451}
2007/10/22 The Power Train Oil Lines Group is Updated {3016, 3154}
CCS7 Compactor Machine Systems Articulating and Oscillating Hitch