Differential and Bevel Gear - Remove
`
770 and 772 Off-Highway Trucks Power Train
[RENR8259]
770 and 772 Off-Highway Trucks Power Train
Transmission Hydraulic Control - Assemble
770 and 772 Off-Highway Trucks Power Train
Differential and Bevel Gear - Disassemble
POWER TRAIN
DIFFERENTIAL & BEVEL GEAR GP
770 and 772 Off-Highway Trucks Power Train
Differential and Bevel Gear - Remove
770 and 772 Off-Highway Trucks Power Train
Differential and Bevel Gear - Disassemble
770 and 772 Off-Highway Trucks Power Train
Differential and Bevel Gear - Install
770 and 772 Off-Highway Trucks Power Train
Rear Axle Housing and Differential - Remove
770 and 772 Off-Highway Trucks Power Train
Rear Axle Housing and Differential - Install
770 and 772 Off-Highway Trucks Power Train
Differential and Bevel Gear - Assemble
1.1. Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 180-3033 | Jack Stand Gp | 1 |
| B | 1U-6130 | Guide Stud | 2 |
Start By:
- Remove the rear axle housing and the differential. Refer to Disassembly and Assembly, "Rear Axle Housing and Differential - Remove".
- Remove the shafts. Refer to Disassembly and Assembly, "Axle Shafts - Remove".
- Use Tooling (A) and suitable blocking in order to support differential arrangement (1). The weight of the differential arrangement (1) is approximately
830 kg (1830 lb) . - Use a suitable lifting device in order to support the wheel assembly (2). The weight of wheel assembly (2) is approximately
1501 kg (3310 lb) . - Remove two bolts (3) across from each other and insert Tooling (B). Remove remaining bolts (3).
Show/hide table
Illustration 3 g01413918 - Separate wheel assembly (2) from differential arrangement (1). Remove O-ring seal (4).
- Repeat Steps 1 through 4 for the other side.
Show/hide table
| |
| Illustration 1 | g01413883 |
Show/hide table
| |
| Illustration 2 | g01413904 |
Information System:
140M and 150 Motor Grader Power Train
Gear Pump (Transmission Charging and Scavenge) - Assemble
2007/11/26
New Pressure Switches Update the Wiring Groups and Lines Groups {1408, 4304}
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System
Relief Valve (Main, Drum Propel Pump) - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System
Relief Valve (Charge Pressure, Axle Propel Pump) - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System
Relief Valve (Charge Pressure, Drum Propel Pump) - Test and Adjust
140M and 150 Motor Grader Power Train
Gear Pump (Transmission Charging and Scavenge) - Disassemble
2007/10/08
A New Main Power Relay and Starter Relay are Now Used {4493, 7499}
CB34, CB34XW and CC34 Utility Compactors
Battery Disconnect Switch - If Equipped
160M and 160 Motor Grader Power Train
Transmission Oil Cooler - Install
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems
Hydraulic Oil Contamination - Test
CP54B, CS54B and CS64B Vibratory Soil Compactors Propel System
Propel System Troubleshooting
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System
Hydraulic System Pressure - Release
770 and 772 Off-Highway Trucks Power Train
Differential and Bevel Gear - Disassemble
770 and 772 Off-Highway Trucks Power Train
Differential and Bevel Gear - Install
140M and 150 Motor Graders Engine Supplement
Engine Support (Front) - Remove and Install
2008/01/28
The Lighting Wiring Group is Updated {1408, 1429, 7553}
C32 Engine for D11T Track-Type Tractors
Component Location
140M and 150 Motor Grader
Piston Pump (Hydraulic Fan) - Disassemble
160M and 160 Motor Grader Power Train
Front Axle - Install
140M and 150 Motor Grader
Piston Pump (Hydraulic Fan) - Assemble
3500 Generator Sets
Air Shutoff - Test - Engines That Are Equipped with ADEM II or ADEM III Engine Control Modules (If equipped)
C32 LRC Engine for Track-Type Tractors
Electrical Connectors
CB34, CB34XW and CC34 Utility Compactors
Lifting and Tying Down the Machine
CB34, CB34XW and CC34 Utility Compactors
Towing the Machine