Transmission Oil Cooler - Install
`
160M and 160 Motor Grader Power Train
[RENR9726]
160M and 160 Motor Grader Power Train
Transmission Oil Cooler - Remove
160M and 160 Motor Grader Power Train
Front Axle - Install
POWER TRAIN
COOLER GP
160M and 160 Motor Grader Power Train
Transmission Oil Cooler - Remove
160M and 160 Motor Grader Power Train
Transmission Oil Cooler - Install
1.1. Installation Procedure
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.
- Position the seal and transmission oil cooler (5) to the machine. Install bolts (4).
Show/hide table
Illustration 2 g01412495 - Install bolts (3).
- Connect tube assemblies (2).
Show/hide table
Illustration 3 g01412494 - Install panel (1).
- Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change" or Operation and Maintenance Manual, "Cooling System Extended Life Coolant - Change" for the proper filling procedure.
Show/hide table
| |
| Illustration 1 | g01412509 |
Information System:
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems
Hydraulic Oil Contamination - Test
CP54B, CS54B and CS64B Vibratory Soil Compactors Propel System
Propel System Troubleshooting
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System
Hydraulic System Pressure - Release
160M and 160 Motor Grader Power Train
Transmission Oil Cooler - Remove
140M and 150 Motor Grader Power Train
Differential Lock Valve - Remove and Install
C3.4 Engines for Caterpillar Built Machines
Finding Top Center Position for No. 1 Piston
CB34, CB34XW and CC34 Utility Compactors
Operator Controls
CB34, CB34XW and CC34 Utility Compactors
Safety Messages
Installation of the Power Shift Solenoid{5264, 5479}
Machines Do Not Update in CAESoffice{7604, 7620}
160M and 160 Motor Grader Machine Systems
Fuel Tank - Install
Assembly Procedure for the 789 X Body for Certain Off-Highway Trucks{7258, 7960}
CB34, CB34XW and CC34 Utility Compactors
Battery Disconnect Switch - If Equipped
2007/10/08
A New Main Power Relay and Starter Relay are Now Used {4493, 7499}
140M and 150 Motor Grader Power Train
Gear Pump (Transmission Charging and Scavenge) - Disassemble
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System
Relief Valve (Charge Pressure, Drum Propel Pump) - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System
Relief Valve (Charge Pressure, Axle Propel Pump) - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System
Relief Valve (Main, Drum Propel Pump) - Test and Adjust
2007/11/26
New Pressure Switches Update the Wiring Groups and Lines Groups {1408, 4304}
140M and 150 Motor Grader Power Train
Gear Pump (Transmission Charging and Scavenge) - Assemble
770 and 772 Off-Highway Trucks Power Train
Differential and Bevel Gear - Remove
770 and 772 Off-Highway Trucks Power Train
Differential and Bevel Gear - Disassemble
770 and 772 Off-Highway Trucks Power Train
Differential and Bevel Gear - Install
140M and 150 Motor Graders Engine Supplement
Engine Support (Front) - Remove and Install