160M and 160 Motor Grader Power Train Transmission Oil Cooler - Remove Caterpillar


Transmission Oil Cooler - Remove
`
160M and 160 Motor Grader Power Train [RENR9726]
POWER TRAIN
COOLER GP
160M and 160 Motor Grader Power Train Transmission Oil Cooler - Remove
160M and 160 Motor Grader Power Train Transmission Oil Cooler - Install
1.1. Removal Procedure

Removal Procedure

Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.


------ WARNING! ------

At operating temperature, the engine coolant is hot and under pressure.

Steam can cause personal injury.

Check the coolant level only after the engine has been stopped and the fill cap is cool enough to touch with your bare hand.

Remove the fill cap slowly to relieve pressure.

Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to prevent personal injury.


Note: Put identification marks on all tube assemblies for installation purposes. Plug all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.

  1. Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change" or Operation and Maintenance Manual, "Cooling System Extended Life Coolant - Change" for the proper procedure.


    Illustration 1g01412494

  2. Remove panel (1).


    Illustration 2g01412495

  3. Disconnect tube assemblies (2).

  4. Remove bolts (3).


    Illustration 3g01412509

  5. Remove bolts (4) in order to remove transmission oil cooler (5) and the seal from the machine.

Information System:

140M and 150 Motor Grader Power Train Differential Lock Valve - Remove and Install
C3.4 Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
CB34, CB34XW and CC34 Utility Compactors Operator Controls
CB34, CB34XW and CC34 Utility Compactors Safety Messages
Installation of the Power Shift Solenoid{5264, 5479}
Machines Do Not Update in CAESoffice{7604, 7620}
160M and 160 Motor Grader Machine Systems Fuel Tank - Install
Assembly Procedure for the 789 X Body for Certain Off-Highway Trucks{7258, 7960}
PM-201 Cold Planer C18 Engine Supplement Engine Enclosure (Hood) - Remove and Install
PM-201 Cold Planer C18 Engine Supplement Coolant Tank - Remove and Install
PM-201 Cold Planer C18 Engine Supplement Battery and Battery Cable - Separate and Connect
PM-201 Cold Planer C18 Engine Supplement Battery - Remove and Install
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Hydraulic System Pressure - Release
CP54B, CS54B and CS64B Vibratory Soil Compactors Propel System Propel System Troubleshooting
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Hydraulic Oil Contamination - Test
160M and 160 Motor Grader Power Train Transmission Oil Cooler - Install
CB34, CB34XW and CC34 Utility Compactors Battery Disconnect Switch - If Equipped
2007/10/08 A New Main Power Relay and Starter Relay are Now Used {4493, 7499}
140M and 150 Motor Grader Power Train Gear Pump (Transmission Charging and Scavenge) - Disassemble
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Relief Valve (Charge Pressure, Drum Propel Pump) - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Relief Valve (Charge Pressure, Axle Propel Pump) - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Relief Valve (Main, Drum Propel Pump) - Test and Adjust
2007/11/26 New Pressure Switches Update the Wiring Groups and Lines Groups {1408, 4304}
140M and 150 Motor Grader Power Train Gear Pump (Transmission Charging and Scavenge) - Assemble