160M and 160 Motor Grader Machine Systems Fuel Tank - Install Caterpillar


Fuel Tank - Install
`
1.1. Installation Procedure

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g01412096

  1. Use two people in order to position fuel tank (21) to the machine. The weight of fuel tank (21) is approximately 36 kg (80 lb). Position bracket (20) and install bolts (19).


    Illustration 2g01412092

  2. Position bracket (18) and install bolts (17).


    Illustration 3g01412088

  3. Position bracket (16) and install bolts (15).


    Illustration 4g01412078

  4. Position hose (14). Tighten clamps (13) to a torque of 11 ± 1 N·m (97 ± 9 lb in).


    Illustration 5g01412072

  5. Connect hose assembly (12).


    Illustration 6g01412069

  6. Install tube (9) into hose (11). Tighten clamps (10) to a torque of 11 ± 1 N·m (97 ± 9 lb in).


    Illustration 7g01411882

  7. Install tube (8) (not shown), the washer, and bolt (7). Install hose (4). Connect hose assembly (5). Tighten clamp (6) to a torque of 11 ± 1 N·m (97 ± 9 lb in).


    Illustration 8g01411876

  8. Connect hose (4).


    Illustration 9g01411870

  9. Connect harness assembly (3).


    Illustration 10g01411860

  10. Position step assembly (2) and install bolts (1).

  11. Repeat Steps 1 through 10 in order to install the fuel tank on the opposite side of the machine.

Information System:

Assembly Procedure for the 789 X Body for Certain Off-Highway Trucks{7258, 7960}
PM-201 Cold Planer C18 Engine Supplement Engine Enclosure (Hood) - Remove and Install
PM-201 Cold Planer C18 Engine Supplement Coolant Tank - Remove and Install
PM-201 Cold Planer C18 Engine Supplement Battery and Battery Cable - Separate and Connect
PM-201 Cold Planer C18 Engine Supplement Battery - Remove and Install
PM-201 Cold Planer C18 Engine Supplement Alternator - Remove and Install
PM-201 Cold Planer C18 Engine Supplement Air Cleaner - Remove and Install
PM-201 Cold Planer C18 Engine Supplement Muffler - Remove and Install
160M and 160 Motor Grader Machine Systems Front Frame from Rear Frame (Articulating Hitch) - Separate
160M and 160 Motor Grader Machine Systems Front Frame to Rear Frame (Articulating Hitch) - Connect
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Kickout and Positioner - Adjust
Arctic Conversion for the Engine in a 587R{1355, 1380}
Machines Do Not Update in CAESoffice{7604, 7620}
Installation of the Power Shift Solenoid{5264, 5479}
CB34, CB34XW and CC34 Utility Compactors Safety Messages
CB34, CB34XW and CC34 Utility Compactors Operator Controls
C3.4 Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
140M and 150 Motor Grader Power Train Differential Lock Valve - Remove and Install
160M and 160 Motor Grader Power Train Transmission Oil Cooler - Remove
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Hydraulic System Pressure - Release
CP54B, CS54B and CS64B Vibratory Soil Compactors Propel System Propel System Troubleshooting
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Hydraulic Oil Contamination - Test
160M and 160 Motor Grader Power Train Transmission Oil Cooler - Install
CB34, CB34XW and CC34 Utility Compactors Battery Disconnect Switch - If Equipped