PM-201 Cold Planer C18 Engine Supplement Air Cleaner - Remove and Install Caterpillar


Air Cleaner - Remove and Install
`
PM-201 Cold Planer C18 Engine Supplement [KENR5053]
AIR INLET AND EXHAUST SYSTEM
AIR CLEANER GP
PM-201 Cold Planer C18 Engine Supplement Air Cleaner - Remove and Install
2.1. Installation Procedure

  1. Raise the powered hood assembly.

  1. Turn the disconnect switch to the OFF position.



    Illustration 1g01421018

  1. Loosen clamp (3) and remove body assembly (1) from air cleaner (2) .



    Illustration 2g01421019

  1. Remove air inlet gasket (4) from air cleaner (2) .



    Illustration 3g01421022

  1. Loosen wing nut (6) and remove primary air filter element assembly (5) from air cleaner (2) .



    Illustration 4g01421024

  1. Loosen wing nut (8) and remove secondary air filter element (7) from air cleaner (2) .



    Illustration 5g01421025

  1. Loosen clamps (10) and separate tube assembly (9) from air cleaner (2) .



    Illustration 6g01421026

  1. Remove nuts (11), the washers, the bolts, and air cleaner (2) .

Installation Procedure




    Illustration 7g01421026

  1. Install air cleaner (2), the bolts, the washers, and nuts (11) .



    Illustration 8g01421025

  1. Connect tube assembly (9) to air cleaner (2) and tighten clamps (10) .



    Illustration 9g01421024

  1. Install secondary air filter element (7) to air cleaner (2) and tighten wing nut (8). Torque wing nut (8) to a torque of 14 N·m (10 lb ft).



    Illustration 10g01421022

  1. Install primary air filter element assembly (5) to air cleaner (2) and tighten wing nut (6) .



    Illustration 11g01421019

  1. Install air inlet gasket (4) to air cleaner (2) .



    Illustration 12g01421018

  1. Install body assembly (1) to air cleaner (2) and tighten clamp (3) .

  1. Turn the disconnect switch to the ON position.

  1. Lower the powered hood assembly.

Information System:

PM-201 Cold Planer C18 Engine Supplement Muffler - Remove and Install
160M and 160 Motor Grader Machine Systems Front Frame from Rear Frame (Articulating Hitch) - Separate
160M and 160 Motor Grader Machine Systems Front Frame to Rear Frame (Articulating Hitch) - Connect
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Kickout and Positioner - Adjust
Arctic Conversion for the Engine in a 587R{1355, 1380}
2007/09/24 The Body Exhaust Arrangement is Updated {1061, 1062}
160M and 160 Motor Grader Machine Systems Fuel Tank - Remove
160M and 160 Motor Grader Power Train Front Axle - Remove
Correct Usage of the Oil Rail Plug for the Cylinder Head on C9 Engines{1100}
Transportation Information {7000}
IT38H Integrated Toolcarrier and 938H Wheel Loader Braking and Hydraulic Fan System Service Brake System Pressure - Test
The Proper Procedures for Troubleshooting Mechanical Unit Injectors (MUI){1251, 1264, 1280, 1288, 1290}
PM-201 Cold Planer C18 Engine Supplement Alternator - Remove and Install
PM-201 Cold Planer C18 Engine Supplement Battery - Remove and Install
PM-201 Cold Planer C18 Engine Supplement Battery and Battery Cable - Separate and Connect
PM-201 Cold Planer C18 Engine Supplement Coolant Tank - Remove and Install
PM-201 Cold Planer C18 Engine Supplement Engine Enclosure (Hood) - Remove and Install
Assembly Procedure for the 789 X Body for Certain Off-Highway Trucks{7258, 7960}
160M and 160 Motor Grader Machine Systems Fuel Tank - Install
Machines Do Not Update in CAESoffice{7604, 7620}
Installation of the Power Shift Solenoid{5264, 5479}
CB34, CB34XW and CC34 Utility Compactors Safety Messages
CB34, CB34XW and CC34 Utility Compactors Operator Controls
C3.4 Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston