R1600G Load Haul Dump Power Train Final Drive and Wheel - Remove Caterpillar


Final Drive and Wheel - Remove
`
1.1. Removal Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
228-4583   Lifting Bracket 

Start By:

  1. Remove the tire and rim. Refer to Disassembly and Assembly, "Tire and Rim - Remove and Install".

  2. Remove the axle shaft. Refer to Disassembly and Assembly, "Axle Shaft - Remove".

Note: The following procedure is performed on the front axle. Each final drive and wheel has the same removal procedure.


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.




    Illustration 1g01206466

  1. Install Tooling (A) and a suitable lifting device to final drive and wheel (1). The weight of final drive and wheel (1) is approximately 272 kg (600 lb).

  2. Remove 16 nuts (2) and the washers. Remove final drive and wheel (1).


    Illustration 2g01206467

  3. Remove O-ring seal (3).

Information System:

R1600G Load Haul Dump Power Train Oscillating Axle (Rear) - Remove
R1600G Load Haul Dump Power Train Fixed Axle (Front) - Install
R1600G Load Haul Dump Power Train Fixed Axle (Front) - Remove
R1600G Load Haul Dump Power Train Tire and Rim - Install
R1600G Load Haul Dump Power Train Tire and Rim - Remove
140M and 150 Motor Graders Engine Supplement Air Compressor - Remove and Install
160M and 160 Motor Grader Machine Systems Wheel Lean Cylinder - Remove and Install
CP76 and CS76 Vibratory Compactors Propel System Pump Synchronization - Test and Adjust
797B Off-Highway Truck Braking System Oil Cooler (Fan Drive, Front Brake, Steering)
CP76 and CS76 Vibratory Compactors Propel System Parking Brake - Test
CP76 and CS76 Vibratory Compactors Propel System Travel Speed - Check
CS56, CS64, CS74, CS76, CP56, CP64, CP74 and CP76 Vibratory Soil Compactors Fuel System Primary Filter (Water Separator) - Replace
R1600G Load Haul Dump Power Train Final Drive and Wheel - Install
R1600G Load Haul Dump Power Train Oscillating Axle (Rear) - Install
CP76 and CS76 Vibratory Compactors Propel System Piston Motor Flushing Valve (Drum) - Test and Replace
CS56, CS64, CS74, CS76, CP56, CP64, CP74 and CP76 Vibratory Soil Compactors Parking Brake - Check
CP76 and CS76 Vibratory Compactors Propel System Piston Motor Flushing Valve (Axle) - Test and Replace
561N Pipelayer Maintenance Interval Schedule
Multiple Registration Messages Occur with Product Link{733T, 7606}
Parts Stock Cylinder Head Assemblies with Rust Preventative Applied{1100}
CP76 and CS76 Vibratory Compactors Propel System Pressure Override Valve (Drum Propel Pump) - Test and Adjust
CP76 and CS76 Vibratory Compactors Propel System Pressure Override Valve (Axle Propel Pump) - Test and Adjust
140M and 150 Motor Grader Piston Pump (All Wheel Drive) - Remove
3176C Engine for the R1600G and the R1700G Load Haul Dumps Cat Data Link - Test