R1600G Load Haul Dump Power Train Tire and Rim - Remove Caterpillar


Tire and Rim - Remove
`
R1600G Load Haul Dump Power Train [KENR6828]
POWER TRAIN
WHEEL GP
R1600G Load Haul Dump Power Train Tire and Rim - Remove
R1600G Load Haul Dump Power Train Tire and Rim - Install
1.1. Removal Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
304-6014  Stand As 
307-0949  Stand As 
214-9268  Wheel Nut Extension Socket 
228-4570  Tire Installation Frame 

Start By:

  1. Install the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".

Note: The procedure for the removal of the front tire and rim assemblies is the same as the procedure for the removal of the rear tire and rim assemblies.

------ WARNING! ------

Follow the recommended procedure for removal and installation of tires and or wheel assemblies.

Ensure that the machine and tire and or wheel assembly are properly supported at all times.

Improper procedures that are used to remove and install tires and or wheel assemblies can result in personal injury or death.


------ WARNING! ------

Improper blocking of the rear axle housing can cause personal injury.

The rear axle housing is made to oscillate. During removal and installation of the rear tires and rims, the rear axle housing must be prevented from oscillating.

Place wood blocks between the rear axle housing and the rear main frame to prevent oscillation of the rear axle housing.




    Illustration 1g01081633
    Typical example

  1. Install wood block (1) between the rear axle housing and the rear frame on both sides of the machine, as shown. This will prevent the rear axle from oscillating.

    Note: The blocks should be a neat fit.



    Illustration 2g01206468

  2. Raise the rear of the machine and place Tooling (B) under the machine in the position shown in Illustration 2.

  3. Raise the front of the machine and place Tooling (A) under the machine in the position shown in Illustration 2.

  4. Lower the worktool to the ground.


    Illustration 3g01206469

  5. Attach a suitable lifting device to Tooling (D). The weight of Tooling (D) is approximately 425 kg (935 lb).

  6. Position Tooling (D) on tire and rim assembly (3), as shown.

  7. Use Tooling (C) (not shown) to remove 20 nuts (2) (not shown) from the rim.

  8. Remove tire and rim assembly (3). The combined weight of tire and rim assembly (3) and of Tooling (D) is approximately 1025 kg (2260 lb).

  9. Repeat Step 5 through Step 8 to remove the remaining tire and rim assemblies.

Information System:

140M and 150 Motor Graders Engine Supplement Air Compressor - Remove and Install
160M and 160 Motor Grader Machine Systems Wheel Lean Cylinder - Remove and Install
CP76 and CS76 Vibratory Compactors Propel System Pump Synchronization - Test and Adjust
797B Off-Highway Truck Braking System Oil Cooler (Fan Drive, Front Brake, Steering)
CP76 and CS76 Vibratory Compactors Propel System Parking Brake - Test
CP76 and CS76 Vibratory Compactors Propel System Travel Speed - Check
CS56, CS64, CS74, CS76, CP56, CP64, CP74 and CP76 Vibratory Soil Compactors Fuel System Primary Filter (Water Separator) - Replace
2007/08/27 The Traction Control System (If Equipped) is Updated {1408, 4801}
CS54 and CP54 Vibratory Soil Compactors Fuel System Primary Filter - Clean/Inspect/Replace
CP76 and CS76 Vibratory Compactors Propel System Case Drain Flow for Piston Motor (Axle Propel) - Test
CS54 and CP54 Vibratory Soil Compactors Fuel System Secondary Filter - Replace
2007/08/27 New AccuGrade Software is Now Available {7220, 7620}
R1600G Load Haul Dump Power Train Tire and Rim - Install
R1600G Load Haul Dump Power Train Fixed Axle (Front) - Remove
R1600G Load Haul Dump Power Train Fixed Axle (Front) - Install
R1600G Load Haul Dump Power Train Oscillating Axle (Rear) - Remove
R1600G Load Haul Dump Power Train Final Drive and Wheel - Remove
R1600G Load Haul Dump Power Train Final Drive and Wheel - Install
R1600G Load Haul Dump Power Train Oscillating Axle (Rear) - Install
CP76 and CS76 Vibratory Compactors Propel System Piston Motor Flushing Valve (Drum) - Test and Replace
CS56, CS64, CS74, CS76, CP56, CP64, CP74 and CP76 Vibratory Soil Compactors Parking Brake - Check
CP76 and CS76 Vibratory Compactors Propel System Piston Motor Flushing Valve (Axle) - Test and Replace
561N Pipelayer Maintenance Interval Schedule
Multiple Registration Messages Occur with Product Link{733T, 7606}