AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0324 - FMI 06 Caterpillar


MID 030 - CID 0324 - FMI 06
`

Conditions Which Generate This Code:




Illustration 1g00928849

Schematic for the action lamp

This diagnostic code is recorded when the main display module reads the voltage of the circuit for the action lamp and the current is above normal. The action lamp does not light as a result of this diagnostic code. The schematic that is shown above represents a typical installation of the component. Verify the connector contact and the wire numbers by utilizing the Electrical System Schematic for the machine that is being serviced.

Test Step 1. CHECK THE LAMP.

  1. At the action lamp, disconnect wire A487-PU from the lamp socket.

Expected Result:

The CID 0324 FMI 06 is present.

Results:

  • OK - The CID 0324 FMI 06 is present. The action lamp is not causing the diagnostic code. Proceed to test step 2.

  • NOT OK - The CID 0324 FMI 06 is NO longer present. The lamp or the lamp socket has failed. The correct resistance for a lamp is greater than 10 ohms.

    Repair: Replace the action lamp.

    Stop.

Test Step 2. CHECK THE HARNESS.

  1. Turn the disconnect switch to the OFF position.

  1. Wire A487-PU remains disconnected from the action lamp.

  1. Disconnect the machine harness from the main display module.

  1. At the machine harness connector for the main display module, measure the resistance between contact 13 (A487-PU) and frame ground.

Expected Result:

The resistance is greater than 5000 ohms.

Results:

  • OK - The resistance is greater than 5000 ohms. The harness resistance is correct. Proceed to test step 3.

  • NOT OK - The resistance is less than 5000 ohms. The harness has failed.

    Repair: Repair the machine harness or replace the machine harness.

    Stop.

Test Step 3. CHECK THE MAIN DISPLAY MODULE.

  1. Remove contact 13 from the machine harness connector for the main display module.

  1. Reconnect the harness connector to the main display module.

  1. Turn the disconnect switch and the key start switches to the ON position.

  1. Place the same diagnostic code on hold. Check the service code indicator.

Expected Result:

The CID 0324 FMI 06 is present.

Results:

  • OK - The CID 0324 FMI 06 remains present. The main display module has failed.

    Repair: It is unlikely that the main display module has failed. Exit this procedure and perform this procedure again. Also, recheck if the diagnostic code indicator is illuminated for this diagnostic code. If the cause of the diagnostic code is not found, replace the main display module. See Troubleshooting, "Main Display Module - Replace".

    Stop.

  • NOT OK - The diagnostic code is NO longer active. The diagnostic code does not exist at this time. The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation. Stop.

Information System:

AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0324 - FMI 05
574B Forwarder Power Train Braking System
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0271 - FMI 06
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0271 - FMI 05
R2900 Load Haul Dump Autoshift Control (Wheel Steering)
R2900 Load Haul Dump Autoshift Control (STIC Steering)
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0263 - FMI 04
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0263 - FMI 03
14H Motor Grader Machine Systems Centershift Lock - Install
14H Motor Grader Machine Systems Centershift Lock - Remove
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Machine Preparation for Troubleshooting
D5N Track-Type Tractor Seat
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Parking Brake (Travel)
Product Link 151/201 Reference Parts Information
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Summary of Revisions
3524B Engine for Caterpillar Built Machines Camshaft - Remove
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0600 - FMI 04
IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader Operational Checks (Hydraulic System)
IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader Visual Inspection
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0819 - FMI 02
AP-655C and BG-2255C Asphalt Pavers Propel System Piston Pump Flow - Test
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0821 - FMI 03
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0821 - FMI 04
3054E Industrial Engine Introduction