AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1725 - FMI 03 Caterpillar


MID 039 - CID 1725 - FMI 03
`

Conditions Which Generate This Code:




Illustration 1g00956149



Illustration 2g00931873

This diagnostic code is associated with the Position Sensor (Deceleration Pedal) for the operator panel (left station). The FMI 03 means that the ECM has determined that the voltage of the circuit for the sensor is above normal.

Note: When optional deceleration pedals are not present on the machine, verify that "Decel Pedals" selection is set to the Uninstall position in the Configure screen of Cat ET.

The output frequency of the position sensor is approximately 500 Hz. The duty cycle of the signal changes as the position sensor moves. The duty cycle varies from 5 to 95 percent.

A - Approximate position of 10 percent duty cycle

B - Approximate position of 50 percent duty cycle

C - Approximate position of 90 percent duty cycle

The possible causes of this diagnostic code are listed below:

  • The signal circuit for the sensor is open.

  • The signal circuit for the sensor is shorted to the +battery circuit.

  • The sensor has failed.

  • The power circuit or the ground circuit has failed.

  • The ECM has failed. ECM failure is unlikely.

Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1725 FMI 03 is active before performing this procedure.

Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.

System Response:

When the diagnostic code is active, the following response occurs:

  • The machine ECM maintains the pre-fault value until a neutral reset occurs.

  • The sensor defaults to 50% after the neutral reset has taken place.

  • The fault lamp for the propulsion system is activated.

  • The action lamp is ON.

Test Step 1. CHECK FOR POWER AT THE SENSOR.

  1. Do not disconnect the harness connector from the sensor.

  1. Turn the key start switch and the disconnect switch to the ON position.

  1. At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along the voltage supply wire (contact A).

  1. Measure the voltage from contact A to frame ground.

Expected Result:

The voltage is 8.0 ± 0.5 DCV.

Results:

  • OK - The voltage is 8.0 ± 0.5 DCV. Proceed to Test Step 3.

  • NOT OK - The voltage is not 8.0 ± 0.5 DCV. The + battery circuit in the machine harness has failed.

    Repair: Replace the machine harness or repair the machine harness.

    STOP

Test Step 2. CHECK THE RELAY

  1. The key start switch and the disconnect switch remain in the ON position.

  1. Remove relay #1 (operating station) for the propel system from the circuit.

  1. Place a jumper between contact 30 (wire K983-BU) and contact 87a (wire144-GN) at the relay socket.

  1. Check the status of the CID 1725 FMI 03.

Expected Result:

The CID 1725 FMI 03 is active.

Results:

  • OK - The CID 1725 FMI 03 is still active. The relay that was removed is operating properly. Place the relay back into the circuit. Proceed to Test Step 3.

  • NOT OK - The CID 1725 FMI 03 is no longer active. The relay that was removed has failed.

    Repair: Replace the relay.

    STOP

Test Step 3. CHECK FOR PROPER GROUND AT THE SENSOR.

  1. The machine harness remains connected to the sensor.

  1. Turn the key start switch and the disconnect switch to the OFF position.

  1. Remove the 7X-1710 Multimeter Probe from the voltage supply wire (contact A).

  1. At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along the ground wire (contact B).

  1. Measure the resistance from contact B to frame ground.

Expected Result:

The resistance is less than 5 ohms.

Results:

  • OK - The resistance is less than 5 ohms. The ground circuit is correct. Proceed to Test Step 4.

  • NOT OK - The resistance is greater than 5 ohms. The ground circuit in the machine harness has failed.

    Repair: Replace the machine harness or repair the machine harness.

    STOP

Test Step 4. CHECK THE WIRING HARNESS OF THE SENSOR FOR AN OPEN CIRCUIT.

  1. The key start switch and the disconnect switch remain in the OFF position.

  1. Disconnect the machine harness from the sensor.

  1. At the harness connector for the sensor, connect a jumper wire between contact B and contact C.

  1. Disconnect the machine harness connectors from the ECM.

  1. At the harness connector for the ECM, measure the resistance between contact J1-2 (wire 370-BU) and contact J1-12 (wire A275-BK).

Expected Result:

The resistance measurement is less than 5 ohms.

Results:

  • OK - The resistance measurement is less than 5 ohms. The circuit is correct. Proceed to Test Step 5.

  • NOT OK - The resistance is greater than 5 ohms. The circuit is not correct. There is an open circuit in the wiring harness.

    Repair: There is an open circuit in the wiring harness. Repair the wiring harness or replace the wiring harness.

    STOP

Test Step 5. CHECK THE WIRING HARNESS OF THE SENSOR FOR A SHORT TO THE +BATTERY CIRCUIT.

  1. The key start switch and the disconnect switch remain in the OFF position.

  1. The machine harness remains disconnected from the sensor. Remove the jumper wire that was installed in the previous step.

  1. The machine harness connectors remain disconnected from the ECM.

  1. At the machine harness connector for the ECM, measure the resistance from the signal contact J1-2 (wire 370-BU) of the machine harness to all contacts that are used in the machine harness connectors for the ECM.

Expected Result:

Each resistance measurement is greater than 5000 ohms.

Results:

  • OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 6.

  • NOT OK - One or more resistance measurements are not correct. There is a short in the machine harness.

    Repair: The short is between signal contact J1-2 (wire 370-BU) and the circuit with the low resistance measurement. Repair the machine harness or replace the machine harness.

    STOP

Test Step 6. CHECK THE OUTPUT OF THE SENSOR.

  1. Reconnect the machine harness connectors to the ECM. Reconnect the machine harness connector to the sensor.

  1. At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along the signal wire (contact C).

  1. At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along the ground wire (contact B).

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Measure the signal of the sensor. The proper signal is described at the beginning of this procedure.

Expected Result:

The signal from the sensor is valid.

Results:

  • OK - The signal from the sensor is valid. Proceed to Test Step 7.

  • NOT OK - The signal from the sensor is not valid.

    Repair: The sensor has failed. Replace the sensor.

    STOP

Test Step 7. CHECK IF THE DIAGNOSTIC CODE REMAINS.

  1. Inspect the contacts of the harness connectors and clean the connectors.

  1. Reconnect all harness connectors.

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Operate the machine.

  1. Check the status of the CID 1725 FMI 03.

Expected Result:

The CID 1725 FMI 03 is active.

Results:

  • YES - The CID 1725 FMI 03 is active. The diagnostic code has not been corrected. The ECM may have failed.

    Repair: ECM failure is unlikely. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace".

    STOP

  • NO - The CID 1725 FMI 03 is not active. The diagnostic code does not exist at this time.

    Repair: The initial diagnostic code may have been caused by a poor electrical connection that was corrected when a harness connector was disconnected and reconnected. Resume normal machine operation

    STOP

Information System:

AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0995 - FMI 06
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0995 - FMI 05
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0995 - FMI 03
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0990 - FMI 08
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0981 - FMI 06
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0981 - FMI 05
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0981 - FMI 03
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0976 - FMI 08
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0681 - FMI 06
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0681 - FMI 03
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0447 - FMI 06
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0447 - FMI 05
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1725 - FMI 04
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1725 - FMI 08
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1726 - FMI 03
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1726 - FMI 04
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1726 - FMI 08
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1727 - FMI 03
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1727 - FMI 04
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1727 - FMI 08
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1728 - FMI 03
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1728 - FMI 04
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1728 - FMI 08
TK711 Track Feller Buncher, TK721 Track Feller Buncher, TK722 Track Feller Buncher and TK732 Track Feller Buncher Machine Systems Main Control Valve - Felling Head