AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0151 - FMI 03 Caterpillar


MID 039 - CID 0151 - FMI 03
`

Conditions Which Generate This Code:




Illustration 1g00943636

Schematic of the Tamper Bar Solenoid

This diagnostic code is associated with the tamper bar solenoid. The FMI 03 means that the ECM has determined that the voltage of the solenoid circuit is above normal.

The possible causes of the diagnostic code are listed:

  • The solenoid has failed.

  • The energize circuit of the solenoid is shorted to the +battery circuit.

  • The ECM has failed. This is unlikely.

Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0151 FMI 03 is active before performing this procedure.

Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.

System Response:

When this diagnostic code is active, the following occurs:

  • The tamper bar runs at full speed.

  • The action lamp is activated.

  • The fault lamp for the material system, the tamp system, and the auxiliary system is activated.

Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO THE +BATTERY CIRCUIT.

  1. Turn the key start switch and the disconnect switch to the OFF position.

  1. Disconnect the machine harness connectors from the solenoid and the ECM.

  1. At the machine harness connector for the ECM, measure the resistance from contact J2-58 (wire C892-GY) to all contacts that are used in the machine harness connectors for the ECM.

Expected Result:

Each resistance measurement is greater than 5000 ohms.

Results:

  • OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 2.

  • NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J2-58 (C892-GY) and the circuit that has a low resistance measurement.

    Repair: Repair the machine harness or replace the machine harness.

    Stop.

Test Step 2. CHECK IF THE DIAGNOSTIC CODE IS STILL ACTIVE.

  1. Inspect the contacts and clean the contacts of the harness connectors.

  1. Reconnect all harness connectors.

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Operate the machine.

  1. Determine if the CID 0151 FMI 03 is active.

Expected Result:

The CID 0151 FMI 03 is active.

Results:

  • YES - The CID 0151 FMI 03 is active. The problem has not been corrected. The ECM may have failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Troubleshooting, "Electronic Control Module (ECM) - Replace".

    Stop.

  • NO - The CID 0151 FMI 03 is not active. The problem does not exist at this time.

    Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.

    Stop.

Information System:

R2900 Load Haul Dump Radiator Core - Clean
533 and 543 Wheel Feller Bunchers Machine Systems Combination Valve (Pilot, Brake, and Steering) - Install
533 and 543 Wheel Feller Bunchers Machine Systems Combination Valve (Pilot, Brake, and Steering) - Remove
533 and 543 Wheel Feller Bunchers Machine Systems Solenoid Valve and Manifold (Disc Saw) - Remove and Install
Product Link 151/201 General Information
322C Forest Machine Hydraulic System Fan Motor Speed (Hydraulic Oil Cooler) - Test and Adjust
Product Link 151/201 Spare Inputs
Product Link 151/201 System Components
Product Link 151/201 Electronic Control Module (ECM)
R2900 Load Haul Dump Lift Arm and Cylinder Bearings - Lubricate
14H Motor Grader Machine Systems Blade - Install
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Vibratory System Bypass Valve (Return Manifold)
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0151 - FMI 05
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0151 - FMI 06
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0291 - FMI 03
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0291 - FMI 05
574B Forwarder Maintenance Interval Schedule
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0291 - FMI 06
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0447 - FMI 03
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0447 - FMI 05
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0447 - FMI 06
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0681 - FMI 03
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0681 - FMI 06
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0976 - FMI 08