Diagnostic Trouble Codes
`
815 Soil Compactor and 816 Landfill Compactor Systems
[M0113643]
815 Soil Compactor and 816 Landfill Compactor Systems
General Information
815 Soil Compactor and 816 Landfill Compactor Systems
Torque Converter
ELECTRICAL AND STARTING SYSTEM
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer
Determining Diagnostic Trouble Codes
814 Wheel Dozer Systems
Diagnostic Capabilities
814 Wheel Dozer Systems
Event Codes
815 Soil Compactor and 816 Landfill Compactor Systems
Diagnostic Trouble Codes
815 Soil Compactor and 816 Landfill Compactor Systems
System Schematic
1.1. Diagnostic Trouble Code (DTC) List
2.2. Transmission ECM
3.2. Implement ECM
The following is a list of Diagnostic Trouble Codes (DTC) for the 815Kand 816K machines. When a diagnostic code becomes active, refer to the Troubleshooting section of this manual for a specific troubleshooting procedure.
Portions of this material are reprinted with permission from SAE J1939DA_201607© 2016 SAE International. SAE International is not responsible for any use or translation of this material, in whole or in part. Contact SAE International to obtain a complete copy of SAE J1939DA_201607, the official definitive source of this standard.
Diagnostic Trouble Code (DTC) List
Each DTC is made up of two numbers. The first number is the Component Identifier (CID). The second number is the Failure Mode Identifier (FMI).
The Module Identifier (MID) identifies the ECM associated with the DTC. For example, MID 081 identifies the Transmission ECM.
Show/hide table
| Diagnostic Trouble Codes for Transmission ECM (MID 081) | ||
|---|---|---|
| DTC | Description | Test Procedure |
| 0041-3 | 8 Volt DC Supply : Voltage Above Normal | Sensor Supply - Test |
| 0041-4 | 8 Volt DC Supply : Voltage Below Normal | Sensor Supply - Test |
| 0070-2 | Parking Brake Switch : Erratic, Intermittent, or Incorrect | Sensor Signal (Analog Active) - Test |
| 0096-3 | Fuel Level Sensor : Voltage Above Normal | Sensor Signal (Analog Active) - Test |
| 0096-4 | Fuel Level Sensor : Voltage Below Normal | Sensor Signal (Analog Active) - Test |
| 0168-3 | Electrical System Voltage : Voltage Above Normal | Electrical Power Supply - Test |
| 0168-4 | Electrical System Voltage : Voltage Below Normal | Electrical Power Supply - Test |
| 0177-3 | Transmission Oil Temperature Sensor : Voltage Above Normal | Sensor Signal (Analog, Passive) - Test |
| 0177-4 | Transmission Oil Temperature Sensor : Voltage Below Normal | Sensor Signal (Analog, Passive) - Test |
| 0177-4 | Transmission Oil Temperature Sensor : Voltage Below Normal | Sensor Signal (Analog, Passive) - Test |
| 0177-8 | Transmission Oil Temperature Sensor : Abnormal Frequency, Pulse Width, or Period | Sensor Signal (Analog, Passive) - Test |
| 0247-9 | SAE J1939 Data Link : Abnormal Update Rate | CAN Data Link - Test |
| 0247-14 | SAE J1939 Data Link : Special Instruction | CAN Data Link - Test |
| 0262-3 | 5 Volt Sensor DC Power Supply : Voltage Above Normal | Sensor Supply - Test |
| 0262-4 | 5 Volt Sensor DC Power Supply : Voltage Below Normal | Sensor Supply - Test |
| 0271-3 | Action Alarm : Voltage Above Normal | Alarm - Test |
| 0271-5 | Action Alarm : Current Below Normal | Alarm - Test |
| 0271-6 | Action Alarm : Current Above Normal | Alarm - Test |
| 0444-3 | Starter Motor Relay : Voltage Above Normal | Relay - Test |
| 0444-6 | Starter Motor Relay : Current Above Normal | Relay - Test |
| 0585-8 | Transmission Output Speed Sensor #1 : Abnormal Frequency, Pulse Width, or Period | Speed Sensor - Test |
| 0590-9 | Engine Control Module : Abnormal Update Rate | Cat Data Link - Test |
| 0590-14 | Engine Control Module : Special Instruction | Cat Data Link - Test |
| 0596-9 | Implement Control : Abnormal Update Rate | Cat Data Link - Test |
| 0596-14 | Implement Control : Special Instruction | Cat Data Link - Test |
| 0621-3 | Downshift Switch : Voltage Above Normal | Switch Circuits - Test |
| 0621-4 | Downshift Switch : Voltage Below Normal | Switch Circuits - Test |
| 0622-3 | Directional Switch : Voltage Above Normal | Switch Circuits - Test |
| 0622-4 | Upshift Switch : Voltage Below Normal | Switch Circuits - Test |
| 0623-3 | Directional Switch : Voltage Above Normal | Switch Circuits - Test |
| 0623-4 | Directional Switch : Voltage Below Normal | Switch Circuits - Test |
| 0626-3 | Steering/Transmission Lock Switch : Voltage Above Normal | Switch Circuits - Test |
| 0626-4 | Steering/Transmission Lock Switch : Voltage Below Normal | Switch Circuits - Test |
| 0637-3 | Backup Alarm: Voltage above normal | Alarm - Test |
| 0637-6 | Backup Alarm: Current above normal | Alarm - Test |
| 0672-8 | Torque Converter Output Speed Sensor : Abnormal Frequency, Pulse Width, or Period | Speed Sensor - Test |
| 0673-8 | Transmission Output Speed Sensor #2 : Abnormal Frequency, Pulse Width, or Period | Speed Sensor - Test |
| 0681-3 | Parking Brake Solenoid : Voltage Above Normal | Solenoid Valve - Test |
| 0681-5 | Parking Brake Solenoid : Current Below Normal | Solenoid Valve - Test |
| 0681-6 | Parking Brake Solenoid : Current Above Normal | Solenoid Valve - Test |
| 0681-7 | Parking Brake Solenoid : Not Responding Properly | Solenoid Valve - Test |
| 0826-3 | Torque Converter Oil Temperature Sensor : Voltage Above Normal | Sensor Signal (Analog, Passive) - Test |
| 0826-4 | Torque Converter Oil Temperature Sensor : Voltage Below Normal | Sensor Signal (Analog, Passive) - Test |
| 0967-9 | Machine Application : Abnormal Update Rate | CAN Data Link - Test |
| 0967-14 | Machine Application : Special Instruction | CAN Data Link - Test |
| 1326-2 | ECM Location Code : Erratic, Intermittent, or Incorrect | ECM Location Code - Test |
| 1401-3 | Transmission Solenoid 1 : Voltage Above Normal | Solenoid Valve - Test |
| 1401-5 | Transmission Solenoid 1 : Current Below Normal | Solenoid Valve - Test |
| 1401-6 | Transmission Solenoid 1 : Current Above Normal | Solenoid Valve - Test |
| 1401-13 | Transmission Solenoid 1 : Out of Calibration | Solenoid Valve - Test |
| 1402-3 | Transmission Solenoid 2 : Voltage Above Normal | Solenoid Valve - Test |
| 1402-5 | Transmission Solenoid 2 : Current Below Normal | Solenoid Valve - Test |
| 1402-6 | Transmission Solenoid 2 : Current Above Normal | Solenoid Valve - Test |
| 1402-13 | Transmission Solenoid 2 : Out of Calibration | Solenoid Valve - Test |
| 1403-3 | Transmission Solenoid 3 : Voltage Above Normal | Solenoid Valve - Test |
| 1403-5 | Transmission Solenoid 3 : Current Below Normal | Solenoid Valve - Test |
| 1403-6 | Transmission Solenoid 3 : Current Above Normal | Solenoid Valve - Test |
| 1403-13 | Transmission Solenoid 3 : Out of Calibration | Solenoid Valve - Test |
| 1404-3 | Transmission Solenoid 4 : Voltage Above Normal | Solenoid Valve - Test |
| 1404-5 | Transmission Solenoid 4 : Current Below Normal | Solenoid Valve - Test |
| 1404-6 | Transmission Solenoid 4 : Current Above Normal | Solenoid Valve - Test |
| 1404-13 | Transmission Solenoid 4 : Out of Calibration | Solenoid Valve - Test |
| 1405-3 | Transmission Solenoid 5 : Voltage Above Normal | Solenoid Valve - Test |
| 1405-5 | Transmission Solenoid 5 : Current Below Normal | Solenoid Valve - Test |
| 1405-6 | Transmission Solenoid 5 : Current Above Normal | Solenoid Valve - Test |
| 1405-13 | Transmission Solenoid 5 : Out of Calibration | Solenoid Valve - Test |
| 1406-3 | Transmission Solenoid 6 : Voltage Above Normal | Solenoid Valve - Test |
| 1406-5 | Transmission Solenoid 6 : Current Below Normal | Solenoid Valve - Test |
| 1406-6 | Transmission Solenoid 6 : Current Above Normal | Solenoid Valve - Test |
| 1406-13 | Transmission Solenoid 6 : Out of Calibration | Solenoid Valve - Test |
| 1628-3 | Armrest Position Switch : Voltage Above Normal | Switch Circuits - Test |
| 1628-4 | Armrest Position Switch : Voltage Below Normal | Switch Circuits - Test |
| 1693-3 | Decelerator Pedal Sensor : Voltage Above Normal | Sensor Signal (PWM) - Test |
| 1693-4 | Decelerator Pedal Sensor : Voltage Below Normal | Sensor Signal (PWM) - Test |
| 1693-8 | Decelerator Pedal Sensor : Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
| 1693-13 | Decelerator Pedal Sensor : Out of Calibration | Sensor Signal (PWM) - Test |
| 1834-2 | Ignition Key Switch loss of signal | Switch Circuits - Test |
| 2448-9 | Graphical Display Module : Abnormal Update Rate | Cat Data Link - Test |
| 2976-3 | Parking Brake Oil Pressure Sensor : Voltage Above Normal | Sensor Signal (PWM) - Test |
| 2976-4 | Parking Brake Oil Pressure Sensor : Voltage Below Normal | Sensor Signal (PWM) - Test |
| 2976-8 | Parking Brake Oil Pressure Sensor : Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
| 2987-3 | Brake Charge Pressure Sensor #1 : Voltage Above Normal | Sensor Signal (PWM) - Test |
| 2987-4 | Brake Charge Pressure Sensor #1 : Voltage Below Normal | Sensor Signal (PWM) - Test |
| 2987-8 | Brake Charge Pressure Sensor #1 : Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
| 3467-3 | Main Power Relay : Voltage Above Normal | Relay - Test |
| 3467-5 | Main Power Relay : Current Below Normal | Relay - Test |
| 3467-6 | Main Power Relay : Current Above Normal | Relay - Test |
| 3470-3 | Machine Power Distribution Relay : Voltage Above Normal | Relay - Test |
| 3470-5 | Machine Power Distribution Relay : Current Below Normal | Relay - Test |
| 3470-6 | Machine Power Distribution Relay : Current Above Normal | Relay - Test |
| 3583-9 | Switch Panel #1 : Abnormal Update Rate | Cat Data Link - Test |
| 3797-3 | Operator Seat Belt Switch : Voltage Above Normal | Switch Circuits - Test |
| 3797-4 | Operator Seat Belt Switch : Voltage Below Normal | Switch Circuits - Test |
Show/hide table
| Diagnostic Trouble Codes For Implement ECM (MID 082) | ||
|---|---|---|
| DTC | Description | Test Procedure |
| 0041-3 | 8 Volt DC Supply : Voltage Above Normal | Sensor Supply - Test |
| 0041-4 | 8 Volt DC Supply : Voltage Below Normal | Sensor Supply - Test |
| 0168-3 | Electrical System Voltage : Voltage Above Normal | Electrical Power Supply - Test |
| 0168-4 | Electrical System Voltage : Voltage Below Normal | Electrical Power Supply - Test |
| 0247-9 | SAE J1939 Data Link : Abnormal Update Rate | CAN Data Link - Test |
| 0247-14 | SAE J1939 Data Link : Special Instruction | CAN Data Link - Test |
| 0262-3 | 5 Volt Sensor DC Power Supply : Voltage Above Normal | Sensor Supply - Test |
| 0262-4 | 5 Volt Sensor DC Power Supply : Voltage Below Normal | Sensor Supply - Test |
| 0268-2 | Programmed Parameter Fault : Erratic, Intermittent, or Incorrect | Parameter - Test |
| 0296-9 | Transmission Control : Abnormal Update Rate | Cat Data Link - Test |
| 0296-14 | Transmission Control : Special Instruction | Cat Data Link - Test |
| 0358-3 | Implement Pilot Pressure Supply Solenoid : Voltage Above Normal | Solenoid Valve - Test |
| 0358-5 | Implement Pilot Pressure Supply Solenoid : Current Below Normal | Solenoid Valve - Test |
| 0358-6 | Implement Pilot Pressure Supply Solenoid : Current Above Normal | Solenoid Valve - Test |
| 0490-3 | Implement Lockout Switch : Voltage Above Normal | Switch Circuits - Test |
| 0490-4 | Implement Lockout Switch : Voltage Below Normal | Switch Circuits - Test |
| 0497-3 | Tilt Right Solenoid: Voltage above normal | Solenoid Valve - Test |
| 0497-5 | Tilt Right Solenoid: Current below normal | Solenoid Valve - Test |
| 0497-6 | Tilt Right Solenoid: Current above normal | Solenoid Valve - Test |
| 0497-13 | Tilt Right Solenoid: Out of calibration | Solenoid Valve - Test |
| 0498-3 | Tilt Left Solenoid: Voltage above normal | Solenoid Valve - Test |
| 0498-5 | Tilt Left Solenoid: Current below normal | Solenoid Valve - Test |
| 0498-6 | Tilt Left Solenoid: Current above normal | Solenoid Valve - Test |
| 0498-13 | Tilt Left Solenoid: Out of calibration | Solenoid Valve - Test |
| 0590-9 | Engine Control Module : Abnormal Update Rate | Cat Data Link - Test |
| 0590-14 | Engine Control Module : Special Instruction | Cat Data Link - Test |
| 0600-3 | Hydraulic Oil Temperature Sensor : Voltage Above Normal | Sensor Signal (Analog, Passive) - Test |
| 0600-4 | Hydraulic Oil Temperature Sensor : Voltage Below Normal | Sensor Signal (Analog, Passive) - Test |
| 0779-3 | Cab Air Temperature Sensor : Voltage Above Normal | Sensor Signal (Analog, Passive) - Test |
| 0779-4 | Cab Air Temperature Sensor : Voltage Below Normal | Sensor Signal (Analog, Passive) - Test |
| 0967-9 | Machine Application : Abnormal Update Rate | CAN Data Link - Test |
| 0967-14 | Machine Application : Special Instruction | CAN Data Link - Test |
| 1078-3 | Blade Control Handle Lift Position Sensor : Voltage Above Normal | Sensor Signal (PWM) - Test |
| 1078-4 | Blade Control Handle Lift Position Sensor : Voltage Below Normal | Sensor Signal (PWM) - Test |
| 1078-8 | Blade Control Handle Lift Position Sensor : Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
| 1078-13 | Blade Control Handle Lift Position Sensor : Out of Calibration | Sensor Signal (PWM) - Test |
| 1079-3 | Blade Control Handle Tilt Position Sensor : Voltage Above Normal | Sensor Signal (PWM) - Test |
| 1079-4 | Blade Control Handle Tilt Position Sensor : Voltage Below Normal | Sensor Signal (PWM) - Test |
| 1079-8 | Blade Control Handle Tilt Position Sensor : Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
| 1079-13 | Blade Control Handle Tilt Position Sensor : Out of Calibration | Sensor Signal (PWM) - Test |
| 1197-3 | Blade Lower Solenoid : Voltage Above Normal | Solenoid Valve - Test |
| 1197-5 | Blade Lower Solenoid : Current Below Normal | Solenoid Valve - Test |
| 1197-6 | Blade Lower Solenoid : Current Above Normal | Solenoid Valve - Test |
| 1197-13 | Blade Lower Solenoid : Out of Calibration | Solenoid Valve - Test |
| 1198-3 | Blade Raise Solenoid : Voltage Above Normal | Solenoid Valve - Test |
| 1198-5 | Blade Raise Solenoid : Current Below Normal | Solenoid Valve - Test |
| 1198-6 | Blade Raise Solenoid : Current Above Normal | Solenoid Valve - Test |
| 1198-13 | Blade Raise Solenoid : Out of Calibration | Solenoid Valve - Test |
| 1326-2 | ECM Location Code : Erratic, Intermittent, or Incorrect | ECM Location Code - Test |
| 1482-3 | 10 Volt Sensor DC Power Supply : Voltage Above Normal | Sensor Supply - Test |
| 1482-4 | 10 Volt Sensor DC Power Supply : Voltage Below Normal | Sensor Supply - Test |
| 1870-3 | Blade Control Handle Thumb Rocker Position Sensor : Voltage Above Normal | Sensor Signal (PWM) - Test |
| 1870-4 | Blade Control Handle Thumb Rocker Position Sensor : Voltage Below Normal | Sensor Signal (PWM) - Test |
| 1870-8 | Blade Control Handle Thumb Rocker Position Sensor : Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
| 1870-13 | Blade Control Handle Thumb Rocker Position Sensor : Out of Calibration | Sensor Signal (PWM) - Test |
| 2114-3 | Blade Control Handle Trigger Switch : Voltage Above Normal | Switch Circuits - Test |
| 2114-4 | Blade Control Handle Trigger Switch : Voltage Below Normal | Switch Circuits - Test |
| 2357-3 | Air Conditioner Evaporator Coil Temperature Sensor : Voltage Above Normal | Sensor Signal (Analog, Passive) - Test |
| 2357-4 | Air Conditioner Evaporator Coil Temperature Sensor : Voltage Below Normal | Sensor Signal (Analog, Passive) - Test |
| 2659-2 | Cab Air Temperature Control Switch : Erratic, Intermittent, or Incorrect | Switch Circuits - Test |
| 2661-3 | Cab Air Temperature Control : Voltage Above Normal | Sensor Signal (Analog, Active) - Test |
| 2661-4 | Cab Air Temperature Control : Voltage Below Normal | Sensor Signal (Analog, Active) - Test |
| 2663-3 | Cab Ventilation Duct Temperature Sensor : Voltage Above Normal | Sensor Signal (Analog, Passive) - Test |
| 2663-4 | Cab Ventilation Duct Temperature Sensor : Voltage Below Normal | Sensor Signal (Analog, Passive) - Test |
| 2671-3 | Air Conditioner Compressor Clutch Solenoid : Voltage Above Normal | Solenoid Valve - Test |
| 2671-4 | Air Conditioner Compressor Clutch Solenoid : Current Below Normal | Solenoid Valve - Test |
| 2671-6 | Air Conditioner Compressor Clutch Solenoid : Current Above Normal | Solenoid Valve - Test |
| 2811-3 | Cab Blower Speed Control : Voltage Above Normal | Switch Circuits - Test |
| 2811-4 | Cab Blower Speed Control : Voltage Below Normal | Switch Circuits - Test |
| 3654-3 | Implement Pump Pressure Sensor : Voltage Above Normal | Sensor Signal (PWM) - Test |
| 3654-4 | Implement Pump Pressure Sensor : Voltage Below Normal | Sensor Signal (PWM) - Test |
| 3654-8 | Implement Pump Pressure Sensor : Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
Information System:
814 Wheel Dozer Systems
Blade and Mounting
815 Soil Compactor and 816 Landfill Compactor Systems
General Information
Improved Engine Hood Group Is Now Used on Certain 140 GC Motor Graders {7251}
Improved Hinge Assembly for the Hood Group Is Now Used on Certain 140 GC Motor Graders {7251}
Water in Fuel Sensor O-Ring on Certain C4.4 and C7.1 Machine Engines {7422}
Water in Fuel Sensor O-Ring on Certain C4.4 and C7.1 Engines {7422}
814 Wheel Dozer Systems
Connector Contact Description
814 Wheel Dozer Systems
Transmission
814 Wheel Dozer Systems
Torque Converter
The Support Bracket for the Clean Exhaust Module May Rub Against the Clean Air Supply Line on Certain 770G and 772G Off-Highway Trucks {108D, 108E, 7553}
New Air Compressor Group Is Now Available for Certain Motor Graders {1803}
814 Wheel Dozer Systems
Rollover Protective Structure (ROPS)
Installation of New THR-3816U Macromatic Time Delay Relay on Certain Asphalt Pavers {1408, 4490}
814 Wheel Dozer Systems
Blade and Mounting
Procedure to Rework the Rear LADAR Cover for R1700 Load Haul Dump Machines Equipped with Command for Underground {7600}
Improved Hitch Bolt Assembly Process Is Now Used on Certain 140 GC Motor Graders {7057, 7100}
Procedure to Install the Implement Control Levers on Certain Motor Graders {5051, 5063, 726A, 795C}
815 Soil Compactor and 816 Landfill Compactor Systems
Torque Converter
740 GC, 740 Ejector, 745 Articulated Truck Power Train
Spindle, Service Brake, and Wheel - Remove and Install
815 Soil Compactor and 816 Landfill Compactor Systems
Transmission
C9 Engine for Caterpillar Built Machines
Crankshaft Rear Seal - Remove and Install
815 Soil Compactor and 816 Landfill Compactor Systems
Alarm - Test
740 GC, 740 Ejector, 745 Articulated Truck Power Train
Spindle, Service Brake, and Wheel - Assemble
815 Soil Compactor and 816 Landfill Compactor Systems
CAN Data Link - Test