TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Pump Control (Output Flow) - Adjust Caterpillar


Pump Control (Output Flow) - Adjust
`
1.1. Adjustment of the Maximum Output Flow of the Pump

------ WARNING! ------

Personal injury or death can result from sudden machine movement.

Sudden movement of the machine can cause injury to persons on or near the machine.

To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.

----------------------

------ WARNING! ------

Personal injury or death can result from escaping fluid under pressure.

Escaping fluid under pressure, even a very small pin-hole size leak, can penetrate body tissue and cause serious injury and possible death. If fluid is injected into your skin, it must be treated immediately by a doctor familiar with this type of injury.

Always use a board or cardboard when checking for a leak.

----------------------

Note: Use the information in the reference to prepare the machine for this test. Also, use the information in the reference to relieve any system pressure that may be present in the hydraulic system.

Reference: For the correct procedure to prepare the machine for this test, refer to Testing and Adjusting, "Machine Preparation for Troubleshooting" for the machine that is being serviced.

Reference: For the correct procedure to relieve any hydraulic oil pressure that may be present in the hydraulic system, refer to Testing and Adjusting, "System Pressure - Release" for the machine that is being serviced.

Adjust the pump output flow if the flow test results differ greatly from the specifications.

Move the machine to level ground.

Lower the work tool to the ground.




Illustration 1g01052558

Location of the switch for the hood on early machines




Illustration 2g01162235

Location of the switch for the hood on later machines




Illustration 3g01074453

Open the hood for the engine compartment.

Note: The switch for the hood is located under the right armrest on early machines. On later machines, the switch for the hood is located on the right hand console.

Shut off the engine.

Adjustment of the Maximum Output Flow of the Pump




Illustration 4g01078245

Main Hydraulic Pumps

(1) Adjustment screw for travel pump. (2) Adjustment screw for implement pump.

Adjust the maximum output flow of the travel pump.

  1. Loosen the locknut.

  1. In order to adjust maximum output flow, turn the screw. Turning screw (1) clockwise will decrease the maximum output flow of the travel pump. Turning screw (1) counterclockwise will increase the maximum output flow of the travel pump.

  1. Tighten the locknut.

  1. Adjust the maximum output flow of the implement pump. Use screw (2) instead of screw (1). Repeat Steps 1 through 3.

Reference: After you adjust the flow of the pump, run the pump flow test. Refer to Testing and Adjusting, "Pump Flow - Test".

Information System:

14H Motor Grader Machine Systems Combination Valve - Remove
Bench Test Procedure for Hydraulic Piston Pumps {4268, 4306, 5070}
Bench Test Procedure for Hydraulic Piston Pumps{5070}
14H Motor Grader Machine Systems Wheel Lean Bar - Remove and Install
Test Sequence for Capsule Type Fuel Nozzles{0782}
14H Motor Grader Machine Systems Blade Lift Cylinder - Remove and Install
CB-634D Paving Compactor Machine Electronic Control System Service Tools
574B Forwarder Power Train On/Off Switches
D350E and D400E Articulated Trucks Power Train Lockup Clutch and Solenoid Valve
574B Forwarder Power Train Accelerator Pedal
3054E Industrial Engine Camshaft Bearings - Remove and Install
793C and 793C XQ Off-Highway Truck Steering System Steering Linkage and Cylinder Mounting
14H Motor Grader Machine Systems Bank Valve - Remove
14H Motor Grader Machine Systems Bank Valve - Install
2002/10/28 Examine Failed Starting Motors to Understand the Reason for Failure {1453}
AP-655C and BG-2255C Asphalt Pavers Propel System Pressure Limiter Valve - Test and Adjust
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System Test/Enable Switch
574B Forwarder Power Train Introduction
C15 Petroleum Generator Set Engines Electric Starting Motor
3126B Machine Engines 5 Volt Engine Pressure Sensor Supply Circuit - Test
AP-655C and BG-2255C Asphalt Pavers Drag Conveyor and Auger Conveyor Systems Piston Pump Flow - Test - Upper and Lower Pump Stacks
14H and 16H Motor Graders Air System and Brakes Quick-Release Valve
3054E Industrial Engine Flywheel - Remove
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Piston Motor (Swing Drive) Case Drain Oil - Measure