C4.4 (Mech) Industrial Engine Engine Oil Cooler - Inspect Caterpillar


Engine Oil Cooler - Inspect
`
C4.4 (Mech) Industrial Engine [KENR6900]
COOLING SYSTEM
COOLER GP
C4.4 (Mech) Industrial Engine Engine Oil Cooler - Inspect
1.1. Introduction
2.1. Inspection Procedure

Introduction

------ WARNING! ------

Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin.


Perform the following procedure in order to inspect the engine oil cooler (if equipped):

Inspection Procedure

  1. Place a container under the oil cooler in order to collect any engine oil or coolant that drains from the oil cooler.

  2. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove" for removal of the engine oil cooler.

  3. Thoroughly clean the flange face of the cover plate and the cylinder block.

  4. Inspect the cooling plates for cracks and dents. Replace the cooling plates if cracks or dents exist.

    If necessary, clean the outside and clean the inside of the cooling plates. Use a solvent that is not corrosive on copper. Ensure that no restrictions for the flow of lubricating oil exist in the cooling plates.

    Dry the cooling plate with low-pressure air. Flush the inside of the cooling plate with clean lubricating oil.

    ------ WARNING! ------

    Personal injury can result from air pressure.

    Personal injury can result without following proper procedure. When using pressure air, wear a protective face shield and protective clothing.

    Maximum air pressure at the nozzle must be less than 205 kPa (30 psi) for cleaning purposes.


  5. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install" for installation of the engine oil cooler.

  6. Ensure that the cooling system and the oil system of the engine are filled to the correct level. Operate the engine. Check for oil or coolant leakage.

Information System:

C4.4 (Mech) Industrial Engine Fuel Injection Nozzle - Test
3054E Industrial Engine Alternator - Test
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0973 - FMI 02
CB-634D Paving Compactor Machine Electronic Control System Reverse Propel
Installation Instructions for the Machine Security System on the Medium Wheel Loaders{7631}
R2900 Load Haul Dump Maintenance Interval Schedule
3126B Machine Engines Sensors and Electrical Connectors
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0972 - FMI 02
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Hydraulic System Main Control Valve - IT38G Series II Integrated Toolcarrier
14H Motor Grader Machine Systems Metering Pump (Steering) - Remove and Install
M318C and M322C Excavators Machine Systems Hydraulic Hand Control - Install - Stabilizer and Blade
M318C Excavator Machine Systems Hydraulic Hand Control - Remove - Stabilizer and Blade
3054E Industrial Engine Power Sources
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0974 - FMI 02
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Operational Checks
AP-655C and BG-2255C Asphalt Pavers Propel System Relief Valve (Charge) - Test and Adjust
14H Motor Grader Machine Systems Wheel - Remove and Install
14H Motor Grader Machine Systems Piston Pump (Hydraulic and Steering) - Install
AP-655C Asphalt Paver Shipping the Machine
A Procedure for the Installation of the Product Link System is Available{7602, 7610, 7620}
14H Motor Grader Machine Systems Solenoid Valve (Centershift Lock) - Remove and Install
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Propel System Pump Control (Manual Displacement Control) Neutral - Test and Adjust
C4.4 (Mech) Industrial Engine Cylinder Head - Inspect
14H Motor Grader Machine Systems Tie Rod (Steering) - Remove and Install