322C Forest Machine Hydraulic System Fan Motor Speed (Hydraulic Oil Cooler) - Test and Adjust Caterpillar


Fan Motor Speed (Hydraulic Oil Cooler) - Test and Adjust
`
1.1. Test
2.1. Adjust

Table 1
Required Tools    
Part Number     Description     Qty    
8T-0859     Pressure Gauge (
25000 kPa (3625 psi))    
1    
9U-7400     Multitach Tool Group     1    



Illustration 1g00817309

Pump compartment

(33) Fan pump

(34) Pressure tap

(35) Relief valve (fan pump)


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on AVSpare products.

Dispose of all fluids according to local regulations and mandates.


Test

  1. Position the machine on level ground.

  1. Stop the engine.

  1. Release the pressure in the hydraulic system. Refer to Testing And Adjusting, "Hydraulic System Pressure - Release".

  1. Install 9U-7400 Multitach Tool Group on the fan for the hydraulic oil cooler.

  1. Start the engine.

  1. Place the machine controls at the following settings: AEC switch OFF and engine speed dial "10".

    ReferenceRefer to Testing And Adjusting, "Engine Performance - Test (Engine Speed)" for engine rpm settings.

  1. Increase the hydraulic oil temperature to 55° ± 5°C (131° ± 9°F).

  1. Read the fan speed. Refer to Table 2 for the correct speed.

    Table 2
    Fan Speed    
    1360 ±10 rpm (1)    
    1730 ±10 rpm (2)    
    ( 1 ) Standard specification
    ( 2 ) High ambient specification

  1. If the fan speed is not within the specification, adjust the relief valve for the fan pump.

Adjust




    Illustration 2g00817311

    Pump compartment

    (35) Relief valve (fan pump)

    (36) Locknut

    (37) Adjustment screw

  1. In order to adjust the relief valve pressure setting for the fan pump, loosen locknut (36) and turn adjustment screw (37) .

    Note: Turning adjustment screw (37) clockwise increases the pressure. Turning adjustment screw (37) counterclockwise decreases the pressure.

    Note: A quarter turn of the relief valve changes the pressure approximately 3300 kPa (480 psi).

    Note: Always make final pressure adjustments on pressure rise.

  1. Adjust the relief valve pressure to the specifications in Table 3.

    Note: In order to avoid hydraulic component damage, adjust the fan speed within the specifications in Table 3.

    Table 3
    Fan Speed     Relief Valve Pressure    
    1360 ±10 rpm (1)    
    8000 kPa (1160 psi)    
    1730 ±10 rpm (2)    
    12900 kPa (1870 psi)    
    ( 1 ) Standard specification
    ( 2 ) High ambient specification

  1. Tighten locknut (36) to a torque of 9.8 ± 0.6 N·m (7 ± 0.4 lb ft).

Information System:

Product Link 151/201 Spare Inputs
Product Link 151/201 System Components
Product Link 151/201 Electronic Control Module (ECM)
R2900 Load Haul Dump Lift Arm and Cylinder Bearings - Lubricate
14H Motor Grader Machine Systems Blade - Install
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Vibratory System Bypass Valve (Return Manifold)
120H and 135H Motor Graders Machine Systems Swivel - Assemble
120H and 135H Motor Graders Machine Systems Swivel - Disassemble
D350E and D400E Articulated Trucks Power Train Front Axle
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Vibratory System Piston Pump (Vibratory System)
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Vibratory System Piston Motor (Vibratory System)
14H Motor Grader Machine Systems Swivel - Install
Product Link 151/201 General Information
533 and 543 Wheel Feller Bunchers Machine Systems Solenoid Valve and Manifold (Disc Saw) - Remove and Install
533 and 543 Wheel Feller Bunchers Machine Systems Combination Valve (Pilot, Brake, and Steering) - Remove
533 and 543 Wheel Feller Bunchers Machine Systems Combination Valve (Pilot, Brake, and Steering) - Install
R2900 Load Haul Dump Radiator Core - Clean
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0151 - FMI 03
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0151 - FMI 05
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0151 - FMI 06
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0291 - FMI 03
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0291 - FMI 05
574B Forwarder Maintenance Interval Schedule
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0291 - FMI 06