CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Case Drain Flow for Piston Motor (Vibratory) - Test Caterpillar


Case Drain Flow for Piston Motor (Vibratory) - Test
`
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems [KENR5723]
HYDRAULIC SYSTEM
MOTOR GP
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Case Drain Flow for Piston Motor (Vibratory) - Test
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Piston Motor (Vibratory)

------ WARNING! ------

Personal injury or death can result from sudden machine movement.

Sudden movement of the machine can cause injury to persons on or near the machine.

To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.


------ WARNING! ------

Personal injury can result from hydraulic oil pressure and hot oil.

Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.

Make sure all of the attachments have been lowered, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.


------ WARNING! ------

Personal injury can result from rotating and moving parts.

Moving fan blades and moving parts will throw or cut any object or tool that falls or is pushed into them.

Make sure no one is working on, underneath or close to an engine that is running. Make sure the area is free of personnel.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Tools and Shop Products Guide", for tools and supplies suitable to collect and contain fluids in AVSpare machines.

Dispose of all fluids according to local regulations and mandates.



NOTICE

In order to avoid damage to the vibrator system during testing, always perform the testing with the vibrator drum on top of tires or on loose dirt. Tires will simulate a non-compacted soil condition

Never operate the vibrator system when the machine is on concrete.



NOTICE

If a testing time longer than three minutes is required, rotate the drum periodically in order to lubricate the eccentric weight shaft bearings.


Table 1
Required Tools 
Tool  Part
Number 
Description  Qty 
4C-8689  Flow Meter Gp
1.9 to 18.9 L/min (0.5 to 5.0 US gpm) 
6V-8556 Nut 
6V-8942 O-Ring Reducer 
6V-8398 O-Ring Seal 
8C-6874 Connector 
124-2117 Coupling 
122-6870 Hydraulic Hose
762 mm (30 inch) 
4C-6500  Digital Thermometer 

  1. Drive the machine to a smooth, horizontal surface on loose, uncompacted soil.

    Note: If loose, uncompacted soil is unavailable, drive the machine onto an unusable, unmounted tire without rims and with a carcass of substantial stiffness to support the drum. If tires are used, the drum should be a minimum of 102 mm (4 inch) above the ground.



    Illustration 1g01412481

  2. Move propulsion lever (1) to the NEUTRAL position.


    Illustration 2g01412483

  3. Move parking brake switch (2) to the ON position.


    Illustration 3g01412484

  4. Move throttle switch (3) to the LOW IDLE position.


    Illustration 4g01412486

  5. Move engine start switch (4) to the OFF position.

  6. Assemble Tool (A).


    Illustration 5g01415320

  7. Disconnect case drain line (5) from the vibratory motor.

  8. Connect the inlet hose from Tool (A) to the vibratory motor. Connect case drain line (5) to the outlet port of the flow meter of Tool (A).

  9. Move engine start switch (4) to the START position. Release the switch when the engine starts.

  10. Operate the engine at low idle for few minutes. Move throttle switch (3) to the HIGH IDLE position.

  11. Monitor the hydraulic oil temperature with Tool (B). Operate the machine until the oil temperature reaches 43 ± 5.6 °C (110 ± 10 °F).

  12. Read the flow on Tool (A). The flow should be less than 3.8 L/min (1.0 US gpm).


    Illustration 6g01415324

  13. Move amplitude selector switch (6) to the LOW AMPLITUDE position.


    Illustration 7g01415328

  14. Depress vibratory switch (7) on top of propulsion lever in order to start the vibratory system.

  15. Read the flow on the flow meter. The flow should be between 5.7 L/min (1.5 US gpm) and 8.7 L/min (2.3 US gpm).

  16. Depress vibratory switch (7) on top of propulsion lever in order to stop the vibratory system.

  17. Move amplitude selector switch (6) to the HIGH AMPLITUDE position.

  18. Depress vibratory switch (7) on top of propulsion lever in order to start the vibratory system.

  19. Read the flow on the flow meter. The flow should be between 5.7 L/min (1.5 US gpm) and 8.7 L/min (2.3 US gpm).

  20. Depress vibratory switch (7) on top of propulsion lever in order to stop the vibratory system.

  21. Move throttle switch (3) to the LOW IDLE position.

  22. Move engine start switch (4) to the OFF position.

  23. Remove Tool (A) from the vibratory pump and reconnect case drain line (5).

Information System:

VIMS Communicator Troubleshooting
140M and 150 Motor Grader Power Train Gear Pump (Transmission Charging and Scavenge) - Install
140M and 150 Motor Grader Power Train Gear Pump (Transmission Charging and Scavenge) - Remove
CP54 and CS54 Vibratory Soil Compactors Machine Systems Hydraulic Oil Contamination - Test
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Magnetic Sensor (Vibratory) - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Vibratory Frequency - Test and Adjust - Fixed
C32 Engine for D11T Track-Type Tractors Inlet Air Temperature Is High
C27 and C32 Engines for Caterpillar Built Machines Exhaust Temperature Is High
C32 Engine for D11T Track-Type Tractors Fuel Temperature Is High
C32 Engine for D11T Track-Type Tractors Fuel Filter Is Restricted
CP54 and CS54 Vibratory Soil Compactors Machine Systems System Pressure - Release
140M and 150 Motor Grader Window Wiper and Wiper Motor (Door) - Remove and Install - Side
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Piston Motor (Vibratory) - Test - Cooling Valve
The Lubrication Sleeve in the Planetary Case and Parts Group is Inadequately Retained on some Off-Highway Trucks{3030, 3064, 3160, 7540}
24M Motor Grader Power Train Electronic Control System MID 027 - CID 1473 - FMI 14
140M and 150 Motor Grader Window Wiper and Wiper Motor (Door) - Remove and Install - Door
CS54 and CP54 Vibratory Soil Compactors Operation Information
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Piston Pump Neutral (Vibratory) - Test and Adjust
AccuGrade Dealer ARO Installation For M-Series, M-Series 2, and M-Series 3 Motor Graders {7220}
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Gear Pump Flow (Steering) - Test
C32 Engine for D11T Track-Type Tractors CAN Data Link - Test
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Gear Pump Flow (Cooling Fan) - Test
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Relief Valve (Steering) - Test
120M and 12M Motor Grader Machine Systems Blade Lift Arm - Remove