CP76 and CS76 Vibratory Compactors Propel System Neutral Start Switch - Test and Adjust Caterpillar


Neutral Start Switch - Test and Adjust
`
CP76 and CS76 Vibratory Compactors Propel System [KENR6089]
ELECTRICAL AND STARTING SYSTEM
SWITCH GP
CP76 and CS76 Vibratory Compactors Propel System Neutral Start Switch - Test and Adjust

------ WARNING! ------

Personal injury can result from rotating and moving parts. Stay clear of all rotating and moving parts.

Never attempt adjustments while the machine is moving or the engine is running unless otherwise specified.

The machine must be parked on a level surface and the engine stopped.

Attach a "Do Not Operate" or similar warning tag to the start switch and controls before servicing, repairing, or making adjustments to the machine.

----------------------

------ WARNING! ------

Personal injury or death can result from sudden machine movement.

Sudden movement of the machine can cause injury to persons on or near the machine.

To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.

----------------------

Table 1
Required Tools    
Tool     Part
Number    
Description     Qty    
A     146-4080     Digital Multimeter Gp     1    
B     7X-1710     Multimeter Probe     1    

  1. Drive the machine to a smooth, horizontal surface.



    Illustration 1g01407630

  1. Move propulsion lever (1) to the NEUTRAL position.



    Illustration 2g01407609

  1. Move parking brake switch (2) to the ON position.



    Illustration 3g01407610

  1. Move throttle switch (3) to the LOW IDLE position.



    Illustration 4g01407660

  1. Move engine start switch (4) to the OFF position.

  1. Raise the cab. Refer to Disassembly and Assembly, KENR6413, "Cab - Tilt".



    Illustration 5g01410344

    The Drum Pump is Shown From Left Side.

  1. Disconnect tie rod (5) .



    Illustration 6g01410347

    The Axle Pump is Shown From Left Side.

  1. Disconnect electrical connector (6) for the neutral start switch.

  1. Insert Tool (B) into pin "1" of electrical connector (6) .

  1. Insert Tool (C) into pin "2" of electrical connector (6).

  1. Connect Tool (B) to Tool (A).

  1. Connect Tool (C) to Tool (A) .

  1. Set Tool (A) to measure continuity.



    Illustration 7g01410350

  1. Ensure that direction control valve (7) on the axle pump is in the NEUTRAL position.



    Illustration 8g01410352

    The Axle Pump is Shown From Left Side.

  1. Loosen locknut (9). If necessary, rotate neutral start switch (8) counterclockwise until the circuit across the switch is open.

  1. Rotate neutral start switch (8) clockwise until the circuit across the switch just closes.

  1. Hold neutral start switch (8). Tighten locknut (9) .

  1. Remove Tool (B) and Tool (C) .

  1. Reconnect electrical connector (6) for the neutral start switch.

  1. Install tie rod (5) .

  1. Lower the cab. Refer to Disassembly and Assembly, KENR6413, "Cab - Tilt".

  1. Move engine start switch (4) to the START position. Release the switch when the engine starts. If the engine will not start, go to Step 6. If the engine starts, go to Step 23.

  1. Move engine start switch (4) to the OFF position.

  1. Move propulsion lever (1) slightly out of NEUTRAL and into the FORWARD range.

  1. Move engine start switch (4) to the START position. If the engine starts, immediately stop the engine, and go to Step 6. If the engine does not start, move the engine start switch to the OFF position. Move propulsion lever (1) to the NEUTRAL position.

  1. Move propulsion lever (1) slightly out of NEUTRAL and into the REVERSE range.

  1. Move engine start switch (4) to the START position. If the engine starts, immediately stop the engine, and go to Step 6. If the engine does not start, move the engine start switch to the OFF position. Move propulsion lever (1) to the NEUTRAL position.

Information System:

3176C Engine for the R1600G and the R1700G Load Haul Dumps Engine Misfires, Runs Rough or Is Unstable
CP76 and CS76 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Axle Propel) - Test and Adjust
3176C, 3406E and 3456 Industrial Engines Engine Cranks but Does Not Start
CS56, CS64, CS74, CS76, CP56, CP64, CP74 and CP76 Vibratory Soil Compactors Engine and Machine Warm-Up
Supplemental Parts Information for the USN Seabee AP655C{1000, 7000}
3176C Engine for the R1600G and the R1700G Load Haul Dumps Coolant Temperature Is High
CP76 and CS76 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Drum Propel) - Test and Adjust
3176C Engine for the R1600G and the R1700G Load Haul Dumps Acceleration Is Poor or Throttle Response Is Poor
CAESultra v3.2 Software Installation{7604, 7620}
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Pilot Oil Accumulator (Dead Engine, Lift Arm Lower) - Test and Charge
3176C Engine for Caterpillar Built Machines Electronic Service Tool Does Not Communicate
3176C Engine for Caterpillar Built Machines ECM - Replace
3176C, 3406E and 3456 Industrial Engines Engine Shutdown Is Intermittent
3176C Engine for the R1600G and the R1700G Load Haul Dumps Engine Top Speed Is Not Obtained
140M and 150 Motor Graders Engine Supplement Aftercooler - Install
R1600G Load Haul Dump Braking System Brake Disc Wear - Check
R1600G Load Haul Dump Braking System Parking Brake - Manual Release
R1600G Load Haul Dump Machine Systems Steering Cylinder - Remove
R1600G Load Haul Dump Machine Systems Main Control Valve - Remove
R1600G Load Haul Dump Machine Systems Main Control Valve - Install
R1600G Load Haul Dump Machine Systems Tilt Lever and Tilt Link - Remove
R1600G Load Haul Dump Machine Systems Tilt Lever and Tilt Link - Install
2007/09/24 An Improved Fuse and ARC Suppressor is Now Used in the Axle Oil Cooler Wiring Harness {1365, 1408}
140H and 160H Motor Graders Changing Direction and Speed