3054E Industrial Engine Power Sources Caterpillar


Power Sources
`
1.1. Data Links
2.1. Power Supply for the ECM
3.1. Power Supply for the Fuel Injection Pump
4.1. Power Supply for the Pressure Sensors
5.1. Power Supply for the Throttle Position Sensor

The 3054E engine has the following power supplies:

  • Data links

  • ECM

  • Fuel injection pump

  • Pressure sensors

  • Throttle position sensor

Data Links



Illustration 1g00938680
Schematic for AVS Data Link (CDL) and J1939 CAN data link

The 3054E engines are equipped with three separate data links. The AVS Data Link (CDL) is used to configure the parameters in the ECM on the electronic service tool. The J1939 CAN data link is used for flash programming for the ECM. Refer to Illustration 1.

The third data link is a proprietary CAN data link which is the communication link between the engine ECM and the Electronic Control Unit (ECU) on the fuel injection pump. Refer to Illustration 3.

Power Supply for the ECM



Illustration 2g01366976
Power supply for the ECM

The power supply to the ECM and the system is drawn from the 12 or 24 volt battery. The power supply for the ECM has the following components:

  • Battery

  • Disconnect switch

  • Key start switch

  • Fuses

  • Ground bolt

  • ECM connector

  • Machine interface connector

Note: The ground bolt is the only component that is mounted on the engine.

The schematic for the ECM shows the main components for a typical power supply circuit. Battery voltage is normally connected to the ECM. The input from the key start switch turns on the ECM.

The wiring harness can be bypassed for troubleshooting purposes. The display screen on the electronic service tool can be used to check the voltage supply.

Note: Two wires are used to reduce resistance.

Power Supply for the Fuel Injection Pump



Illustration 3g01141661
Power supply for the fuel injection pump


Illustration 4g00931447
Connection for the fuel injection pump (J40/P40)


Illustration 5g01143327
Connector for the fuel injection pump (J40)
(1) Can -
(2) Can +
(3) Unused
(4) Unused
(5) Fuel shutoff
(6) Pump supply -
(7) Pump supply +
(8) Signal for primary speed/timing sensor
(9) Unused

The power supply for the ECM comes from the machine interface connector. The machine interface connector receives power from the power relay.

Power Supply for the Pressure Sensors



Illustration 6g01366978
Schematic for pressure sensors

The ECM supplies 5.0 ± 0.2 DC volts to the ECM connector on each sensor. The power supply is protected against short circuits. A short in a sensor or a wiring harness will not cause damage to the ECM.

Power Supply for the Throttle Position Sensor



Illustration 7g00938717
Schematic for the throttle position sensor

The ECM supplies 8.0 ± 0.4 DC volts through the ECM connector to the sensor. The power supply is protected against short circuits. A short in a sensor or a wiring harness will not cause damage to the ECM.

Information System:

C4.4 (Mech) Industrial Engine Engine Oil Cooler - Inspect
C4.4 (Mech) Industrial Engine Fuel Injection Nozzle - Test
3054E Industrial Engine Alternator - Test
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0973 - FMI 02
CB-634D Paving Compactor Machine Electronic Control System Reverse Propel
Installation Instructions for the Machine Security System on the Medium Wheel Loaders{7631}
R2900 Load Haul Dump Maintenance Interval Schedule
3126B Machine Engines Sensors and Electrical Connectors
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0972 - FMI 02
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Hydraulic System Main Control Valve - IT38G Series II Integrated Toolcarrier
14H Motor Grader Machine Systems Metering Pump (Steering) - Remove and Install
M318C and M322C Excavators Machine Systems Hydraulic Hand Control - Install - Stabilizer and Blade
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0974 - FMI 02
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Operational Checks
AP-655C and BG-2255C Asphalt Pavers Propel System Relief Valve (Charge) - Test and Adjust
14H Motor Grader Machine Systems Wheel - Remove and Install
14H Motor Grader Machine Systems Piston Pump (Hydraulic and Steering) - Install
AP-655C Asphalt Paver Shipping the Machine
A Procedure for the Installation of the Product Link System is Available{7602, 7610, 7620}
14H Motor Grader Machine Systems Solenoid Valve (Centershift Lock) - Remove and Install
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Propel System Pump Control (Manual Displacement Control) Neutral - Test and Adjust
C4.4 (Mech) Industrial Engine Cylinder Head - Inspect
14H Motor Grader Machine Systems Tie Rod (Steering) - Remove and Install
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Harvester Head System - Test