14M and 16M Motor Graders Machine Systems General Information - Autolube System, If Equipped Caterpillar


General Information - Autolube System, If Equipped
`


Illustration 1g01408708
Location of the lubrication system components


Illustration 2g01408858
View of Area "A"
(1) Port for the rod end of the wheel lean cylinder
(2) Port for the upper bearing of the right steering pivot
(3) Port for the bearing of the right lean arm
(4) Port for the front bearing of the right axle mounting
(5) Port for the rear bearing of the right axle mounting
(6) Port for the rod end of the right steering cylinder
(7) Port for the lower bearing of the right steering pivot
(8) Port for the ball of the drawbar
(9) Port for the right bearing on the steering link
(10) Port for the cylinder end of the right steering cylinder
(11) Port for the cylinder end of the wheel lean cylinder


Illustration 3g01409367
View of Area "B"
(12) Port for the rod end of the center shift cylinder
(13) Port for the upper bearing of the left steering pivot
(14) Port for the bearing of the left lean arm
(15) Port for the front bearing of the left axle mounting
(16) Port for the rear bearing of the left axle mounting
(17) Port for the rod end of the left steering cylinder
(18) Port for the lower bearing of the left steering pivot
(19) Port for the front bearing of the axle assembly
(20) Port for the left bearing of the steering link
(21) Port for the rear bearing of the axle assembly
(22) Port for the cylinder end of the steering cylinder


Illustration 4g01409689
View of Area "C"
(23) Lubrication tank
(24) Electric pump motor


Illustration 5g01409749
View of Area "D"
(25) Port for the rod end of the left lift cylinder
(26) Port for the cylinder end of the center shift cylinder
(27) Port for the rod end of the right lift cylinder


Illustration 6g01409789
View of Area "E"
(28) Port for the upper bearing of the articulation hitch
(29) Port for the lower bearing of the articulation hitch


Illustration 7g01409802
View of Area "F"
(30) Port for the right bearing for the cylinder support
(31) Port for the shaft of the rod end of the cylinder
(32) Port for the left bearing of the cylinder support

Information System:

CP76 and CS76 Vibratory Compactors Propel System Piston Pump Neutral (Drum Propel Pump) - Adjust
14M Motor Grader Operator Controls
140M and 150 Motor Graders Engine Supplement Aftercooler - Remove
140H and 160H Motor Graders Maintenance Interval Schedule
R1600G Load Haul Dump Parking Brake Manual Release
R1600G Load Haul Dump Engine and Machine Warm-Up
Reuse and Salvage for Turbochargers {0760, 0767, 1052}
924H, 924HZ, 928HZ and 930H Wheel Loaders MID 081 - CID 1960 - FMI 09
140M and 150 Motor Graders Engine Supplement Fuel Priming Pump and Water Separator - Remove and Install
Bench Test Procedure For A 784B, 784C, 785B, 785C, and 785D Off-Highway Truck Torque Converter{3101}
3176C Engine for the R1600G and the R1700G Load Haul Dumps Timing - Calibrate
797 Rear Wheel Bearing Full Single Life Reusability Guidelines {4201}
CP76 and CS76 Vibratory Compactors Propel System Piston Pump Neutral (Axle Propel Pump) - Adjust
3176C Engine for Caterpillar Built Machines ECM - Replace
3176C Engine for Caterpillar Built Machines Electronic Service Tool Does Not Communicate
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Pilot Oil Accumulator (Dead Engine, Lift Arm Lower) - Test and Charge
CAESultra v3.2 Software Installation{7604, 7620}
3176C Engine for the R1600G and the R1700G Load Haul Dumps Acceleration Is Poor or Throttle Response Is Poor
CP76 and CS76 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Drum Propel) - Test and Adjust
3176C Engine for the R1600G and the R1700G Load Haul Dumps Coolant Temperature Is High
Supplemental Parts Information for the USN Seabee AP655C{1000, 7000}
CS56, CS64, CS74, CS76, CP56, CP64, CP74 and CP76 Vibratory Soil Compactors Engine and Machine Warm-Up
3176C, 3406E and 3456 Industrial Engines Engine Cranks but Does Not Start
CP76 and CS76 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Axle Propel) - Test and Adjust