D350E and D400E Articulated Trucks Power Train Center Axle Caterpillar


Center Axle
`
1.1. 129-0384 Center Axle
2.1. 123-4853 Center Axle

129-0384 Center Axle




Illustration 1g00929048

(1) 9M-5874 Shim Pack

10 Shims ... 0.08 mm (0.003 inch)

20 Shims ... 0.13 mm (0.005 inch)

Note: Shims must be free of dents and shims must be free of wrinkles.

(2) Torque of drain plug ... 70 ± 15 N·m (52 ± 11 lb ft)

(3) Torque of drain plug ... 70 ± 15 N·m (52 ± 11 lb ft)

(4) Torque the 12 bolts to 200 ± 20 N·m (148 ± 15 lb ft). Turn an additional 60° ± 5°.

(5) Set the end of the pin within 2.4 ± 0.8 mm (0.09 ± 0.03 inch) of the disc. Then tighten the set screw in order to hold the pin in place.

(6) Torque the 16 bolts to 200 ± 20 N·m (148 ± 15 lb ft). Turn an additional 60° ± 5°.

(7) Torque the 36 bolts to 200 ± 20 N·m (148 ± 15 lb ft). Turn an additional 60° ± 5°.

(8) Coat the end of the shaft with 6V-6640 Sealant.

(9) Fill the recess of the square drive after installation. Use a polyester filler.

123-4853 Center Axle




Illustration 2g00928923

(1) 9M-5874 Shim Pack

10 Shims ... 0.08 mm (0.003 inch)

20 Shims ... 0.13 mm (0.005 inch)

Note: Shims must be free of dents and shims must be free of wrinkles.

(2) Torque of drain plug ... 70 ± 15 N·m (52 ± 11 lb ft)

(3) Torque of drain plug ... 70 ± 15 N·m (52 ± 11 lb ft)

(4) Torque the 28 bolts to 200 ± 20 N·m (148 ± 15 lb ft). Turn an additional 60° ± 5°.

(5) Torque the 2 bolts to 200 ± 20 N·m (148 ± 15 lb ft). Turn an additional 60° ± 5°.

(6) Set the end of the pin within 2.4 ± 0.8 mm (0.09 ± 0.03 inch) of the disc. Then tighten the set screw in order to hold the pin in place.

(7) Torque the 2 bolts to 200 ± 20 N·m (148 ± 15 lb ft). Turn an additional 60° ± 5°.

(8) Coat the end of the shaft with 6V-6640 Sealant.

(9) Fill the recess of the square drive after installation. Use a polyester filler.

Information System:

3524B Engine for Caterpillar Built Machines Camshaft - Install
3054E Industrial Engine Introduction
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0821 - FMI 04
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0821 - FMI 03
AP-655C and BG-2255C Asphalt Pavers Propel System Piston Pump Flow - Test
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0819 - FMI 02
IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader Visual Inspection
IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader Operational Checks (Hydraulic System)
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 030 - CID 0600 - FMI 04
3524B Engine for Caterpillar Built Machines Camshaft - Remove
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Summary of Revisions
Product Link 151/201 Reference Parts Information
G3304 and G3306 Engines Visual Inspection
14H and 16H Motor Graders Power Train Introduction
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers Monitoring System - Self Test
Installation of New Restriction Orifice for the Unit Injector Pump
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers Electrical Connector - Inspect
3054E Industrial Engine Basic Engine
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers Main Display Module Initialization - Adjust
Installation Instructions for the Machine Security System on the Small Wheel Loaders{7631}
3524B Engine for Caterpillar Built Machines Accessory Drive (Front) - Remove
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers Connector Contact Description
2002/11/25 An Improved Hose Assembly for Machines with Dual Fuel Tanks is now Used {1710}
Product Link 151/201 MID 122 - CID 0168 - FMI 00