12H, 140H, 143H, 160H and 163H Motor Graders Hydraulic and Steering System Operator Console Caterpillar


Operator Console
`



Illustration 1g01398901

Note: Apply seal (1) to plate (2) . The seal should be centered between the fasteners that are on both sides of the console, as shown.

(1) Approximate length of the seal ... 500 ± 10 mm (19.7 ± 0.4 inch)

(3) Adjust the locking bolt when the console is in the FULL FORWARD position in order to maintain a 20 to 25 mm (0.8 to 1.0 inch) clearance with the instrument panel.

(4) 8C-3442 Coil Spring

Length under test force ... 57.9 mm (2.28 inch)
Test force ... 71.2 ± 5.8 N (16 ± 1.3 lb)
Free length after test ... 50.3 mm (1.98 inch)
Outside diameter ... 17.48 ± 0.25 mm (0.688 ± 0.010 inch)

Note: Apply seal (5) around the opening of cab platform, as shown.

(5) Approximate length of the seal ... 400 ± 10 mm (15.7 ± 0.4 inch)

(6) 3Y-2806 Spring

Length under test force ... 71.1 mm (2.80 inch)
Test force ... 35.50 ± 2.90 N (8.0 ± 0.7 lb)
Free length after test ... 48.5 mm (1.91 inch)
Outside diameter ... 17.80 mm (0.701 inch)

(7) As required, use the bearings to limit the horizontal movement.

Note: Center seal (8) between radii, as shown.

(8) Approximate length of the seal ... 100 ± 10 mm (3.9 ± 0.4 inch)

(9) Torque for the nut ... 1.70 ± 0.25 N·m (15 ± 2 lb in)

(E) Rod length beyond lever ... 28 ± 3 mm (1.1 ± 0.1 inch)

(F) Depth of bearing in two places ... 3.7 ± 1.5 mm (0.15 ± 0.06 inch)

(G) Depth of bearing ... 6.0 ± 2.0 mm (0.24 ± 0.08 inch)




Illustration 2g01398904

Section D-D

(11) Spacer

Note: Thread the cylinder rod (10) into the retainer (12) until the pin (15) contacts the ball (14) . Loosen cylinder rod (10) half of a turn. Apply 4C-4030 Thread Lock Compound to the threads below nut (13) . Tighten the nut (13) .

Note: Before you install the cylinder rod (10) , use 1P-0808 Multipurpose Grease to apply the grease into the cavity of the retainer (12) in order to surround the ball (14) .

Information System:

561M Pipelayer Transmission - Power Shift
928G Wheel Loader Refill Capacities
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Engine Air Filter Secondary Element - Replace
793B Off-Highway Truck Steering System Relief Valve (Steering)
966G and 972G Wheel Loaders Secondary Steering - If Equipped
561M Pipelayer Transmission Selector and Pressure Control Valve - Power Shift
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Fuel System Primary Filter (Water Separator) Element - Replace
12H, 140H and 160H Motor Graders Air System and Brakes Service Brakes
12H, 140H, 143H, 160H and 163H Motor Graders Air System and Brakes Service Brakes
928G Wheel Loader Autoshift Control
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Engine Oil and Filter - Change
793B Off-Highway Truck Steering System Steering Control Valve
12H, 140H, 143H, 160H and 163H Motor Graders Hydraulic and Steering System Valve and Linkage Group
924Gz Wheel Loader Braking System - Test
120H and 135H Motor Graders Hydraulic and Steering System Blade Lift Control Valve
416C, 426C, 428C, 436C and 438C Backhoe Loaders Cooling System Coolant (ELC) - Change
416C, 426C, 428C, 436C and 438C Backhoe Loaders Cooling System Coolant Extender (ELC) - Add
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Radiator Core - Clean
120H and 135H Motor Graders Hydraulic and Steering System Control Valve (Blade Lift)
561M Pipelayer Transmission Controls and Parking Brake Linkage
120H and 135H Motor Graders Power Train Clutch Control (Modulation)
12H, 140H, 143H, 160H and 163H Motor Graders Power Train Selector and Pressure Control Valve
120H and 135H Motor Graders Hydraulic and Steering System Control Valve (Snow Plow/Dozer Lift)
12H, 140H, 143H, 160H and 163H Motor Graders Power Train Selector and Pressure Control Valve