Air Conditioning and Heating R134a for All Caterpillar Machines Refrigerant Compressor Caterpillar


Refrigerant Compressor
`


Illustration 1g06457192

Table 1
Item  Qty  Part  Specification Description 
Apply Loctite 242 or Loctite STS Dri-Loc to magnetic field coil screws and with initial torque of 5.35 ± 0.50 N·m (47.35 ± 4.43 lb in)
Final installation torque is 35 ± 3 N·m (26 ± 2 lb ft)
Note: Oil plug is under pressure when the system is pressurized.
Tighten the oil plug to 14 ± 1 N·m (124 ± 9 lb in)
Displacement per revolution is 82 cc (5 cubic inch)
Maximum allowable continuous speed is 4000 rpm. 
Rotation of the compressor is clockwise. 
Magnetic Clutch: 
Operating voltage is 12 VDC. 
Coil resistance at 20 ° C (68 ° F) is 3.2 ohm. 
Minimum voltage for clutch engagement is 10.5 VDC. 

Information System:

CB22, CB24, CB32 and CC24 Utility Compactors Plate Locations and Film Locations
CB22, CB24, CB32 and CC24 Utility Compactors Specifications
CB22, CB24, CB32 and CC24 Utility Compactors Sound Information and Vibration Information
CB22, CB24, CB32 and CC24 Utility Compactors Safety Messages
140M and 150 Motor Grader Control Manifold (Steering Backup) - Install
140M and 150 Motor Grader Control Manifold (Steering Backup) - Remove
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Pump Neutral (Drum Propel Pump) - Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pressure Override Valve (Axle Propel Pump) - Test and Adjust
140M and 150 Motor Grader Steering Control Valve - Install
140M and 150 Motor Graders Engine Supplement Radiator Guard and Support, Aftercooler, Hydraulic Oil Cooler, and Radiator, - Install
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pressure Override Valve (Drum Propel Pump) - Test and Adjust
R1600G Load Haul Dump Machine Electrical System Actual Gear Indicator
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Pump Neutral (Axle Propel Pump) - Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Drum Propel) - Test and Adjust
2007/10/01 A New Transmission Speed Sensor is Now Available for Series H-Series Motor Graders {3175}
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Axle Propel) - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Neutral Start Switch - Test and Adjust
Replacement of the Blower Assembly on Certain Wheel Loaders{7304, 7320}
2007/10/08 A New Main Power Relay, Starter Relay and Glow Plug Relay are Now Used {1403, 1412, 4493, 7499}
2007/10/08 A New Main Power Relay and Starter Relay are Now Used {4493, 7499}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Piston Ring Groove - Inspect
The Electronic Priming Pump for Machine Engines will not Prime{1258, 1263}
279C, 289C and 299C Compact Track Loaders Reference Material
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Case Drain Flow for Piston Motor (Drum Propel) - Test