CS-563E, CP-563E, CS-573E, CP-573E, CS-583E, CP-583E, CS-663E, CP-663E and CS-683E Vibratory Soil Compactors Engine Oil and Filter - Change Caterpillar


Engine Oil and Filter - Change
`

Run the engine in order to warm up the oil. Stop the engine before you drain the oil. When the oil is warm the waste particles are suspended in the oil. The waste particles will be removed when the oil is drained.

As the oil cools, the waste particles settle to the bottom of the oil pan. The waste particles will not be removed if the oil is too cool.

The waste particles can recirculate through the engine lubrication system if the recommended procedure is not followed.

  1. Open the engine compartment.


    Illustration 1g00930892

  2. Place a suitable container under the drain valve. Open the drain valve. Refer to the Operation and Maintenance Manual, "General Hazard Information" for information that pertains to containing fluid spillage.

  3. Allow the oil to completely drain.

  4. Close the drain valve.


    Illustration 2g00942506

  5. There are two filters. Remove filter elements (1). Discard the used filter elements.

  6. Clean the filter housing bases. All of the old filter seal must be removed from the filter housing base.

  7. Apply a thin coat of engine oil to the seal of the new filter elements.

  8. Install the new filters by hand. When the seal contacts the base, tighten the filter element for an additional 3/4 turn. This will tighten the filter sufficiently.

    Every new oil filter has rotation index marks that are spaced at 90 degree increments. Use the rotation index marks as a guide for tightening the oil filter.



    Illustration 3g00942464

  9. Remove the oil filler plug. Fill the crankcase with new oil. See Operation and Maintenance Manual, "Capacities (Refill)". See Operation and Maintenance Manual, "Lubricant Viscosities". Clean the oil filler cap and install the oil filler cap.

  10. Before you start the engine, check the oil level on the dipstick. The oil level must be within the FULL RANGE on the dipstick.

  11. Start the engine. Run the engine for two minutes. Inspect the machine for leaks. Stop the machine.

  12. Wait for ten minutes in order to allow the oil to drain back into the crankcase. Check the oil level. Maintain the oil level within the FULL RANGE on the dipstick.

  13. Close the engine compartment.

Information System:

3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks Engine Overspeed Lamp and Engine Overspeed Alarm
CS-563E, CP-563E, CS-573E, CP-573E, CS-583E, CP-583E, CS-663E, CP-663E and CS-683E Vibratory Soil Compactors Engine Oil Sample - Obtain
CS-563E, CP-563E, CS-573E, CP-573E, CS-583E, CP-583E, CS-663E, CP-663E and CS-683E Vibratory Soil Compactors Engine Oil Level - Check
3054E Industrial Engine Engine Valve Lash - Inspect/Adjust
R2900 Load Haul Dump Belts - Inspect/Adjust
3054E Industrial Engine Glow Plugs - Test
CB-434D, CB-534D, CB-534D Series XW and CB-564D Paving Compactors Power Supply Circuit of Electronic Control Module
14H Motor Grader Machine Systems Piston Pump (Hydraulic and Steering) - Remove
3524B Engine for Caterpillar Built Machines Water Pump - Install
14H and 16H Motor Graders Power Train Power Train
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks Service Engine Lamp
CP-563C and CS-563C Vibratory Compactors Engine Air Filter Primary Element - Clean/Replace
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1763 - FMI 02
M318C Excavator Machine Systems Hydraulic Hand Control - Remove - Stabilizer and Blade
M318C and M322C Excavators Machine Systems Hydraulic Hand Control - Install - Stabilizer and Blade
14H Motor Grader Machine Systems Metering Pump (Steering) - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Hydraulic System Main Control Valve - IT38G Series II Integrated Toolcarrier
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0972 - FMI 02
3126B Machine Engines Sensors and Electrical Connectors
R2900 Load Haul Dump Maintenance Interval Schedule
Installation Instructions for the Machine Security System on the Medium Wheel Loaders{7631}
CB-634D Paving Compactor Machine Electronic Control System Reverse Propel
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0973 - FMI 02
3054E Industrial Engine Alternator - Test