CS-563E, CP-563E, CS-573E, CP-573E, CS-583E, CP-583E, CS-663E, CP-663E and CS-683E Vibratory Soil Compactors Engine Oil Level - Check Caterpillar


Engine Oil Level - Check
`
1.1. Add The Engine Oil


NOTICE

Do not under fill or overfill engine crankcase with oil. Either condition can cause engine damage.


Stop the engine in order to check the oil level. DO NOT check the oil level when the engine is running.

Park the machine on a level surface.

  1. Open the engine compartment.


    Illustration 1g00942465

  2. Remove dipstick (1). Wipe the dipstick with a clean cloth. Insert the dipstick. Remove the dipstick and note the oil level. Insert the dipstick.

    Note: Refer to the Operation and Maintenance Manual, "Lubricant Viscosities and Capacities (Refill)" for the correct amount of oil that is used when the oil is changed. The correct amount of oil determines the correct level of the oil in the FULL range on the dipstick.


    NOTICE

    Do not overfill the crankcase. The oil level must not reach the top of the FULL range mark or above the FULL range mark.


  3. Maintain the oil level on the dipstick between the FULL RANGE mark and the ADD OIL mark . Add oil if the oil level is too low.

    Note: Operating your engine with the oil level above the FULL mark in the FULL Range could cause the crankshaft to dip into the oil. This could result in excessively high operating temperatures. The high operating temperatures could result in reduced lubricating characteristics of the oil. This could cause damage to the bearings and loss of engine power.

Add The Engine Oil

  1. Open the engine compartment.


    Illustration 2g00942464

  2. Remove oil filler plug (2).

  3. Add the oil.

  4. Clean the oil filler plug. Install the oil filler plug.

  5. Close the engine compartment.

Information System:

3054E Industrial Engine Engine Valve Lash - Inspect/Adjust
R2900 Load Haul Dump Belts - Inspect/Adjust
3054E Industrial Engine Glow Plugs - Test
CB-434D, CB-534D, CB-534D Series XW and CB-564D Paving Compactors Power Supply Circuit of Electronic Control Module
14H Motor Grader Machine Systems Piston Pump (Hydraulic and Steering) - Remove
3524B Engine for Caterpillar Built Machines Water Pump - Install
14H and 16H Motor Graders Power Train Power Train
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks Service Engine Lamp
CP-563C and CS-563C Vibratory Compactors Engine Air Filter Primary Element - Clean/Replace
R2900 Load Haul Dump Automatic Brake Application System (Low Transmission Oil Pressure) - Test - If Equipped
793B Off-Highway Truck Suspension Cylinder Suspension Cylinder (Rear)
793B Off-Highway Truck Suspension Cylinder Suspension Cylinder (Front)
CS-563E, CP-563E, CS-573E, CP-573E, CS-583E, CP-583E, CS-663E, CP-663E and CS-683E Vibratory Soil Compactors Engine Oil Sample - Obtain
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks Engine Overspeed Lamp and Engine Overspeed Alarm
CS-563E, CP-563E, CS-573E, CP-573E, CS-583E, CP-583E, CS-663E, CP-663E and CS-683E Vibratory Soil Compactors Engine Oil and Filter - Change
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1763 - FMI 02
M318C Excavator Machine Systems Hydraulic Hand Control - Remove - Stabilizer and Blade
M318C and M322C Excavators Machine Systems Hydraulic Hand Control - Install - Stabilizer and Blade
14H Motor Grader Machine Systems Metering Pump (Steering) - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Hydraulic System Main Control Valve - IT38G Series II Integrated Toolcarrier
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0972 - FMI 02
3126B Machine Engines Sensors and Electrical Connectors
R2900 Load Haul Dump Maintenance Interval Schedule
Installation Instructions for the Machine Security System on the Medium Wheel Loaders{7631}