R2900 Load Haul Dump Transmission Oil Filter - Replace Caterpillar


Transmission Oil Filter - Replace
`

The machine must be level, the parking brake engaged and the engine stopped.

------ WARNING! ------

Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin.

----------------------


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on AVSpare products.

Dispose of all fluids according to local regulations and mandates.





Illustration 1g00947619

The transmission oil filter is located under the torque converter access cover.




    Illustration 2g00947620

  1. Remove the drain plug from the bottom of the filter housing and allow the oil to drain into a suitable container.

  1. Use a wrench in order to remove the filter housing.

  1. Remove the used filter element. Dispose of the used filter element properly.

  1. Clean the filter housing with a clean, nonflammable solvent.

  1. Clean the housing base.

  1. Inspect the filter housing seal. Replace the seal if the seal is damaged.

  1. Install a new filter element into the transmission filter housing.

  1. Clean the filter housing drain plug and install the drain plug. Install the filter housing into the filter housing base.

  1. Start and run the engine at low idle. Apply the service brakes. Use the right brake pedal only.

  1. Disengage the parking brake. Slowly operate the transmission controls in order to circulate the transmission oil.

  1. Move the transmission directional control to the NEUTRAL position. Engage the parking brake.

  1. Inspect the transmission oil filter for leaks.



    Illustration 3g00947624

  1. Maintain the transmission oil level between the "LOW" and "FULL" marks on dipstick (1).

  1. Remove the oil filler cap and add oil through filler tube (2), if necessary.

    Reference: For information on lubricants and refill capacities, refer to the Operation and Maintenance Manual, "Lubricant Viscosities and Refill Capacities" for the machine that is being serviced.

  1. Clean and install oil filler cap.

  1. Stop the engine.

Information System:

R2900 Load Haul Dump Transmission Oil - Change
14H and 16H Motor Graders Power Train Differential and Bevel Gear
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Hydraulic System Air - Purge
R2900 Load Haul Dump Tilt Cylinder and Tilt Lever Bearings - Lubricate
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Hydraulic Oil Contamination - Test
574B Forwarder Power Train Gearshift Valve
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System System Pressure - Release
C-15 and C-16 Industrial Engines Summary of Revisions
14H Motor Grader Operator Controls
14H Motor Grader Additional Messages
2002/11/11 A New Transmission Pressure Switch is now Used {3016, 3154}
14H and 16H Motor Graders Power Train Transmission Control Valve
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0070 - FMI 02
3054E Industrial Engine Electrical System
CS-563E, CP-563E, CS-573E, CP-573E, CS-583E, CP-583E, CS-663E, CP-663E and CS-683E Vibratory Soil Compactors Gauges
14H Motor Grader Machine Systems Piston Pump (Fan Drive) - Remove
14H Motor Grader Machine Systems Piston Pump (Fan Drive) - Install
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Swing Speed and Overswing on Level Ground - Check
3054E Industrial Engine Fuel Injection
797B Off-Highway Truck Fan Drive Hydraulic System General Information
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Swing Speed and Swing Drift on a Slope - Check
14H and 16H Motor Graders Power Train Final Drive and Tandem Drive
3054E Industrial Engine Electronic Control System
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Boom Cylinder Drift - Check