14H Motor Grader Additional Messages Caterpillar


Additional Messages
`


Illustration 1g00931032


Illustration 2g00939076

There are several specific messages on this machine. The exact location of the messages and the description of the messages are reviewed in this section. Please become familiarized with all messages.

Make sure that all of the messages are legible. Clean the messages or replace the messages if you cannot read the words. Replace the illustrations if the illustrations are not legible. When you clean the messages, use a cloth, water and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the messages. Loose adhesive will allow the messages to fall.

Replace any message that is damaged, or missing. If a message is attached to a part that is replaced, install a message on the replacement part. Any AVSpare dealer can provide new messages.

Fuel Filler (1)

This message is located on the filler tube for the fuel tanks.



Illustration 3g00907956


NOTICE

Use only a AVSpare approved fast fill system to fuel machines. Over pressurization may cause tank deformation and fuel spillage.

Contact your Cat dealer for fast fill system availability.


Do Not Step. (2)

This message is located on each fuel tank.



Illustration 4g00906093

Do not use the fuel tank as a step.

Do Not Weld the Frame. (3)

This message is located on the left side of the front frame behind the lift cylinder bracket.



Illustration 5g00906095

Do not drill or weld top or bottom plates of main frame.

Alternate Exit (4)

If your machine is equipped with a snow wing, this message is located on the left ROPS support at the rear of the operator's compartment.



Illustration 6g00907967

If the primary exits are blocked, use the hammer to break the window. Exit the machine through the window.

Do Not Weld the ROPS. (5)

This message is located on each ROPS support assembly at the rear of the operator's compartment.



Illustration 7g00906117

Do not weld the ROPS. Do not drill the ROPS. Read the service manual before you perform any work on the ROPS.

Do Not Service the Air Conditioner. (6)

This message is located on the front of the air conditioner under the seat.



Illustration 8g00939074

Read the service manual before you perform any maintenance on the air conditioner.

Information System:

2002/11/11 A New Transmission Pressure Switch is now Used {3016, 3154}
14H and 16H Motor Graders Power Train Transmission Control Valve
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers Fuel Level Sender
C4.4 (Mech) Industrial Engine Lubrication System
2003/01/06 New Flash Software Is Now Used {7620}
3524B Engine for Caterpillar Built Machines Flywheel Housing - Install
574B Forwarder Power Train Differential
D5N Track-Type Tractor Transmission System Oil Sample - Obtain
2002/10/28 Changes to the Pump Drive Improve the Service Life {3016, 3108, 3154}
Product Link 151/201 Reporting Interval Erratic
Product Link 151/201 Operating Hours Discrepancy
Product Link 151/201 Diagnostics and Events Not Available
14H Motor Grader Operator Controls
C-15 and C-16 Industrial Engines Summary of Revisions
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System System Pressure - Release
574B Forwarder Power Train Gearshift Valve
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Hydraulic Oil Contamination - Test
R2900 Load Haul Dump Tilt Cylinder and Tilt Lever Bearings - Lubricate
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Hydraulic System Air - Purge
14H and 16H Motor Graders Power Train Differential and Bevel Gear
R2900 Load Haul Dump Transmission Oil - Change
R2900 Load Haul Dump Transmission Oil Filter - Replace
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0070 - FMI 02
3054E Industrial Engine Electrical System