R2900 Load Haul Dump Hydraulic System Oil Filter - Replace Caterpillar


Hydraulic System Oil Filter - Replace
`

------ WARNING! ------

Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin.

----------------------


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on AVSpare products.

Dispose of all fluids according to local regulations and mandates.





    Illustration 1g00945826

  1. Relieve the hydraulic tank pressure by pushing on top of breaker relief valve (1) before changing the filters.



    Illustration 2g00945827

  1. Remove filter access cover (2) from the hydraulic tank guard.

  1. Remove the filter covers.

  1. Inspect each cover seal for damage. Replace the cover seals, if necessary.

  1. Remove and discard the four filter elements.

  1. Remove oil filler cap (3) .



    Illustration 3g00945828

  1. Remove hydraulic tank oil filler strainer (5). Wash the strainer and the filter covers in clean, nonflammable solvent.

  1. Install filler strainer (5) in the filler tube. Install four new filter elements in the hydraulic tank.



    Illustration 4g00945829

  1. Install the covers. Tighten the cover bolts to 56 ± 3 N·m (41 ± 2 lb ft).

  1. Inspect the oil filler cap gasket. Replace the gasket if it is damaged.

  1. Maintain the hydraulic oil level above the "ADD COLD" mark in sight gauge (4) with the engine stopped and the bucket level on the ground. Add oil, if necessary through the filler tube.

  1. Install oil filler cap (3) .

Information System:

R2900 Load Haul Dump Hydraulic System Oil - Change
D350E and D400E Articulated Trucks Power Train Rear Drive Shaft
2002/10/21 New Electronic Control Modules Used on Machine Engines {1901}
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Propel System Control Valve (Shift)
R2900 Load Haul Dump Hydraulic Line Screen - Clean
3524B Engine for Caterpillar Built Machines Water Temperature Regulators - Remove
R2900 Load Haul Dump Fuel Tank Cap and Strainer - Clean
R2900 Load Haul Dump Fuel System Water Separator - Drain
797 Off-Highway Truck Fan Drive Hydraulic System Fan - Calibrate
R2900 Load Haul Dump Fuel System Secondary Filter - Replace
C9 On-Highway Engines Lubrication System
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Braking System Vane Pump (Braking)
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Braking System Service Brakes
3524B Engine for Caterpillar Built Machines Water Temperature Regulators - Install
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Machine Systems Steering, Fan and Leveling Blade System
C-9 Engine for Caterpillar Built Machines Ether Injection System - Test
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1703 - FMI 03
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Propel System Axle
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Propel System Final Drive Planetary (Drum Propel)
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1703 - FMI 05
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1703 - FMI 06
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Propel System Piston Pump (Axle Propel and Drum Propel)
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Vibratory Soil Compactors Propel System Piston Motor (Axle Propel)
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 1704 - FMI 03