Hydraulic System Oil Filter - Replace
`
IT28G Integrated Toolcarrier
[SEBU7020]
IT28G Integrated Toolcarrier
Hydraulic System Oil - Change
IT28G Integrated Toolcarrier
Hydraulic System Oil Level - Check
HYDRAULIC SYSTEM
TANK GP
IT28G Integrated Toolcarrier
Hydraulic System Oil - Change
IT28G Integrated Toolcarrier
Hydraulic System Oil Filter - Replace
IT28G Integrated Toolcarrier
Hydraulic System Oil Level - Check
Show/hide table
![]() | |
Illustration 1 | g00469114 |
Show/hide table
![]() | |
Illustration 2 | g00101919 |
- Remove the hydraulic tank filler cap that is located under the access panel (1) on the top of the engine compartment. Use the steps (2) and handholds (3) in order to reach the access panel. The steps and handholds are located on the left side of the machine.
- The hydraulic oil filter is located on the right side of the machine. Open the engine access door on the right side of the machine.
Show/hide table
![]() | |
Illustration 3 | g00470121 |
- Remove the filter element with a strap type wrench.
Show/hide table
![]() | |
Illustration 4 | g00101921 |
- Clean the filter element mounting base. Remove any part of the filter element gasket that remains on the filter element mounting base.
- Apply a light coat of oil to the gasket of the new filter element.
- Install the new filter element by hand. When the gasket contacts the filter element mounting base, tighten the filter element for an additional three quarters of a turn.
- Remove the hydraulic tank breather. Replace the old breather with a new breather.
Show/hide table
![]() | |
Illustration 5 | g00102469 |
- Maintain the hydraulic oil level above the "ADD COLD" mark on the sight gauge. Add oil, if necessary.
Show/hide table
![]() | |
Illustration 6 | g00101922 |
- Inspect the gasket on the hydraulic tank filler cap for damage. Replace the gasket, if necessary.
- Install the hydraulic tank filler cap.
- Close the engine access door. Replace the access panel.
Information System:
IT28G Integrated Toolcarrier
Hydraulic System Oil - Change
IT28G Integrated Toolcarrier
Fuel System Primary Filter - Replace
IT28G Integrated Toolcarrier
Equipment Lowering with Engine Stopped
IT28G Integrated Toolcarrier
Engine Oil and Filter - Change
IT28G Integrated Toolcarrier
Cooling System Coolant (DEAC) - Change
793C and 793C XQ Off-Highway Truck Power Train
Oil Filter (Transmission Charging)
793C and 793C XQ Off-Highway Truck Power Train
Gear Pump (Transmission and Torque Converter)
793C and 793C XQ Off-Highway Truck Air System and Brakes
Gear Pump (Hoist and Front Brake Cooling)
3208 Marine Engine
Engine Oil Sample - Obtain
IT28G Integrated Toolcarrier
Engine Air Filter Secondary Element - Replace
3208 Marine Engine
Hoses and Clamps - Inspect/Replace
793B Off-Highway Truck Air System and Brakes
Temperature Sensor (Brake Oil)
IT28G Integrated Toolcarrier
Hydraulic System Oil Level - Check
IT28G Integrated Toolcarrier
Lifting and Tying Down the Machine
IT28G Integrated Toolcarrier
Model View Illustrations
IT28G Integrated Toolcarrier
Product Identification Number, Serial Number and EU's CE Plate Locations
793B Off-Highway Truck Power Train
Relief Valve (Torque Converter Inlet)
793B Off-Highway Truck Power Train
Relief Valve (Torque Converter Outlet)
793B Off-Highway Truck Power Train
Torque Converter
IT28G Integrated Toolcarrier
Single Lever Control
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package
Overhaul Considerations
IT28G Integrated Toolcarrier
Towing the Machine
IT28G Integrated Toolcarrier and 928G Wheel Loader
Torque Converter
IT28G Integrated Toolcarrier
Transmission Oil - Change