561M Pipelayer Seat Adjustment Caterpillar


Seat Adjustment
`



Illustration 1g00039117



Illustration 2g00100018



Illustration 3g00039122

The operator's seat that is provided with this machine is in compliance with the appropriate class of "ISO 7096".

Note: Adjust the seat for a new operator or at the beginning of each shift.

The operator should be seated against the seat backrest. Adjust the seat so that the operator is allowed full travel of the pedals.

Back Angle Adjustment - Lift handle (1) and allow the seat back to tilt forward. Push the front of the backrest. This will tilt the seat backward. Release handle (1) at the desired position.

Adjustment of the Seat Height - Remove the weight from the seat. Lift the seat height level lever (2) to the stop position. Hold handle (2) upward. Raise the seat upward or push the seat downward. Release the handle at one of the three positions.

Fore/Aft Adjustment - Lift up on fore/aft handle (3). Move the seat forward or move the seat rearward until the desired position is attained. Release the handle in order to lock the seat into position.

Angle Adjustment for the Bottom Cushion - Raise tilt control (4) upward. The seat will raise upward. If you push the front of the seat cushion downward, the seat will lower. Release the handle at one of the three positions.

Weight Adjustment - Position the seat between the middle position and the rear position. Extend the lever that is used for cranking from knob (6). Rotate the crank to the minus position for less support. Rotate the crank to the plus position for more support. Refer to indicator (9) for the approximate weight setting. Release the crank at the desired setting.

Adjustment for the Lumbar Support - Rotate knob (7) to one of three positions in order to attain more support for the lower back. Rotate knob (7) to one of three positions in order to attain less support for the lower back.

Retractable Seat Belt - When the seat has been adjusted to fit the operator, secure retractable seat belt (8) .

Extension of the Back Height - Raise upward on extension (5) in order to remove the extension. Reverse this procedure in order to install extension (5).

Information System:

322B, 322B L, 325B and 325B L Excavators Operating Technique Information
IT28G Integrated Toolcarrier Pallet Fork Rated Load
561M Pipelayer Cooling System Additive (DEAC) - Add
631E Series II Wheel Tractor-Scrapers Tire Inflation with Nitrogen
793B Off-Highway Truck Air System and Brakes Service and Parking Brake (Rear)
322B, 322B L, 325B and 325B L Excavators Operation
793B Off-Highway Truck Air System and Brakes Service and Parking Brake (Front)
3208 Marine Engine Cooling System Coolant Extender (ELC) - Add
IT28G Integrated Toolcarrier Material Handling Arm Rated Load
3208 Marine Engine Cooling System Supplemental Coolant Additive (SCA) - Test/Add
IT28G Integrated Toolcarrier Bucket Rated Load
3208 Marine Engine Extended Life Coolant (ELC) Cooling System Maintenance
D6F SR, D6G and D6G SR Track-Type Tractors Operation
322B, 322B L, 325B and 325B L Excavators Boom, Stick and Bucket Operation
IT28G Integrated Toolcarrier V-Belts - Inspect/Adjust/Replace
IT28G Integrated Toolcarrier Attachment Arm and Cylinder Linkage - Lubricate
IT28G Integrated Toolcarrier Battery Electrolyte Level - Check
IT28G Integrated Toolcarrier Bulldozing and Dumping
IT28G Integrated Toolcarrier Cooling System Coolant Additive (DEAC) - Add
IT28G Integrated Toolcarrier Cooling System Level - Check
793C and 793C XQ Off-Highway Truck Air System and Brakes Control Valve (Hoist)
572R Pipelayer General Hazard Information
793B Off-Highway Truck Power Train Lockup Clutch and Synchronizing Valve (Torque Converter)
928G Wheel Loader Alert Indicators