IT28G Integrated Toolcarrier Material Handling Arm Rated Load Caterpillar


Material Handling Arm Rated Load
`

------ WARNING! ------

Failure to comply to the rated load can cause possible personal injury or attachment damage.

Review the rated load of a particular attachment before performing any operation. Make adjustments to the rated load as necessary.

----------------------

Note: Rated loads should be used as a guide. Attachments, uneven ground conditions, soft ground conditions, or poor ground conditions have effects on rated loads. The operator is responsible for being aware of these effects.

The rated operating load is defined by the least amount of weight of the following conditions.

  • 50 percent of the full turn static tipping load

  • The minimum lift capacity

  • The minimum tilt capacity

The placement height (ground line to the chain hook) and reach (front tire to the chain hook) are given for the highest position of the material handling arm and for the lowest position of the material handling arm.




Illustration 1g00104502

Position A represents the retracted position. Position B represents the mid-position. Position C represents the extended position.

The following table provides the rated operating loads for the standard machine configuration with material handling arm.

Table 1
RATED LOAD FOR MATERIAL HANDLING ARM    
Position of Material Handling Arm     Retracted
A    
Mid-Position
B    
Extended
C    
Rated Operating Load    
2095 kg (4619 lb)    

1660 kg (3660 lb)    

1377 kg (3036 lb)    
Placement Height at Lowest Position    
-1502 mm (-4 ft 11 inches)    

-2306 mm (-7 ft 7 inches)    

-3111 mm (-10 ft 2 inches)    
Reach at Lowest Position    
1529 mm (5 ft)    

2122 mm (7 ft)    

2715 mm (8 ft 11 inches)    
Placement Height at Highest Position    
5574 mm (18 ft 2 inches)    

6379 mm (20 ft 11 inches)    

7185 mm (23 ft 7 inches)    
Reach at Highest Position    
1608 mm (5 ft 3 inches)    

2199 mm (7 ft 2 inches)    

2791 mm (9 ft 2 inches)    

Information System:

3208 Marine Engine Cooling System Supplemental Coolant Additive (SCA) - Test/Add
IT28G Integrated Toolcarrier Bucket Rated Load
3208 Marine Engine Extended Life Coolant (ELC) Cooling System Maintenance
793C and 793C XQ Off-Highway Truck Hydraulic System Hoist Cylinder
IT28G Integrated Toolcarrier Cab Air Filter - Clean/Replace
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Braking System Service Brakes
3208 Marine Engine Water/Supplemental Coolant Additive (SCA)
IT28G Integrated Toolcarrier Battery Disconnect Switch
3208 Marine Engine Conventional Coolant/Antifreeze Cooling System Maintenance
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Braking System Vane Pump (Implement, Pilot and Braking)
3208 Marine Engine Coolant Recommendations
3208 Marine Engine General Coolant Information
3208 Marine Engine Cooling System Coolant Extender (ELC) - Add
793B Off-Highway Truck Air System and Brakes Service and Parking Brake (Front)
322B, 322B L, 325B and 325B L Excavators Operation
793B Off-Highway Truck Air System and Brakes Service and Parking Brake (Rear)
631E Series II Wheel Tractor-Scrapers Tire Inflation with Nitrogen
561M Pipelayer Cooling System Additive (DEAC) - Add
IT28G Integrated Toolcarrier Pallet Fork Rated Load
322B, 322B L, 325B and 325B L Excavators Operating Technique Information
561M Pipelayer Seat Adjustment
D6F SR, D6G and D6G SR Track-Type Tractors Operation
322B, 322B L, 325B and 325B L Excavators Boom, Stick and Bucket Operation
IT28G Integrated Toolcarrier V-Belts - Inspect/Adjust/Replace