IT28G Integrated Toolcarrier Bucket Rated Load Caterpillar


Bucket Rated Load
`

------ WARNING! ------

Failure to comply to the rated load can cause possible personal injury or attachment damage. Review the rated load of a particular attachment before performing any operation. Make adjustments to the rated load as necessary.

----------------------

Note: Rated loads should be used as a guide. Attachments, uneven ground conditions, soft ground conditions, or poor ground conditions have effects on rated loads. The operator is responsible for being aware of these effects.

Rated loads are based upon a standard machine with the following conditions:

  • lubricants

  • full fuel tank

  • enclosed ROPS

  • 80 kg (176 lb ) operator

  • 20.5 R25 L2 or equivalent tires

Rated loads will vary with different attachments. Contact your AVSpare dealer regarding the rated load for specific attachments.

The rated operating load is defined by the SAE standard "J818" (May 1987 ) and by the ISO 5998 ( 1986 ) as 50 % of the full turn static tipping load.

The corresponding dump clearance is given for each bucket at maximum lift height and at a 45 degree dump angle. The reach is given for each bucket at maximum lift height and at a 45 degree dump angle. Clearance is measured from the ground to the bucket edge in order to dump the load. The reach is measured from the front tire to the bucket edge.




Illustration 1g00104500

Dimension A represents the dump clearance. Dimension B represents the reach.

The following table provides the rated operating loads for the standard machine configuration with a bucket.

Table 1
RATED BUCKET LOAD    
Bucket Part Number     Ground Engaging Tools     Rated Volume     Rated Operating Load     Dump Clearance
A    
Reach
B    
132-2258     Bolt-on Cutting Edge    
2.0 m3 (2.6 yd3)    

3477 kg (7667 lb)    

2911 mm (9 ft 7 inches)    

1014 mm (3 ft 4 inches)    
Teeth
1.9 m3 (2.5 yd3)    

3521 kg (7764 lb)    

2979 mm (9 ft 9 inches)    

981 mm (3 ft 3 inches)    
Teeth and Segments
2.0 m3 (2.6 yd3)    

3440 kg (7584 lb)    

2911 mm (9 ft 7 inches)    

1014 mm (3 ft 4 inches)    
132-2256     Bolt-on Cutting Edge    
1.8 m3 (2.35 yd3)    

3518 kg (7756 lb)    

2967 mm (9 ft 9 inches)    

958 mm (3 ft 2 inches)    
Teeth
1.7 m3 (2.25 yd3)    

3558 kg (7845 lb)    

3036 mm (9 ft 11 inches)    

924 mm (3 ft)    
Teeth and Segments
1.8 m3 (2.35 yd3)    

3466 kg (7643 lb)    

2967 mm (9 ft 9 inches)    

958 mm (3 ft 2 inches)    
4E-2473     Flush Mount Teeth    
1.7 m3 (2.25 yd3)    

3575 kg (7883 lb)    

3035 mm (9 ft 11 inches)    

923 mm (3 ft)    

Information System:

3208 Marine Engine Extended Life Coolant (ELC) Cooling System Maintenance
793C and 793C XQ Off-Highway Truck Hydraulic System Hoist Cylinder
IT28G Integrated Toolcarrier Cab Air Filter - Clean/Replace
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Braking System Service Brakes
3208 Marine Engine Water/Supplemental Coolant Additive (SCA)
IT28G Integrated Toolcarrier Battery Disconnect Switch
3208 Marine Engine Conventional Coolant/Antifreeze Cooling System Maintenance
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Braking System Vane Pump (Implement, Pilot and Braking)
3208 Marine Engine Coolant Recommendations
3208 Marine Engine General Coolant Information
3208 Marine Engine S·O·S Oil Analysis
3208 Marine Engine Fuel Recommendations
3208 Marine Engine Cooling System Supplemental Coolant Additive (SCA) - Test/Add
IT28G Integrated Toolcarrier Material Handling Arm Rated Load
3208 Marine Engine Cooling System Coolant Extender (ELC) - Add
793B Off-Highway Truck Air System and Brakes Service and Parking Brake (Front)
322B, 322B L, 325B and 325B L Excavators Operation
793B Off-Highway Truck Air System and Brakes Service and Parking Brake (Rear)
631E Series II Wheel Tractor-Scrapers Tire Inflation with Nitrogen
561M Pipelayer Cooling System Additive (DEAC) - Add
IT28G Integrated Toolcarrier Pallet Fork Rated Load
322B, 322B L, 325B and 325B L Excavators Operating Technique Information
561M Pipelayer Seat Adjustment
D6F SR, D6G and D6G SR Track-Type Tractors Operation