IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Transmission Oil Filter - Replace Caterpillar


Transmission Oil Filter - Replace
`
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders [SEBU7018]
POWER TRAIN
FILTER GP
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Transmission Oil Filter - Replace


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.

Dispose of all fluids according to local regulations and mandates.


  1. Park the machine on a hard, level surface. Lower the bucket to the ground with a slight downward pressure. Engage the parking brake and stop the engine.


    Illustration 1g00766360

  2. The transmission oil filter is located on the left side of the machine near the articulation joint. Use a strap type wrench to remove the transmission oil filter. Dispose of the used oil filter properly.

  3. Clean the filter mounting base. Remove all of the used filter gasket from the filter mounting base.


    Illustration 2g00101318

  4. Apply a thin coat of clean transmission oil to the gasket of the new filter element. Install the new filter element by hand. When the gasket contacts the filter mounting base, tighten the transmission oil filter by an additional 3/4 turn.

  5. Start the engine. Slowly operate the transmission controls in order to circulate the transmission oil.

  6. Move the transmission control to the NEUTRAL position. Inspect the transmission oil filter for leaks.

  7. Check the transmission oil level.

    Reference: Refer to Operation and Maintenance Manual, "Transmission Oil Level - Check" for the correct procedure.

Information System:

IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Circuit Breakers - Reset
928G Wheel Loader Shipping the Machine
120H and 135H Motor Graders Air System and Brakes Parking Brake
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Fuses - Replace
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Specifications
928G Wheel Loader Secondary Steering
938G Wheel Loader and IT38G Integrated Toolcarrier Engine Starting with Auxiliary Start Receptacle - If Equipped
554 Forwarder and 574 Forwarder Engine Starting with Jump Start Cables
928G Wheel Loader Starting Below 0°C (32°F) with Thermal Starting Aid
928G Wheel Loader Starting Above 0°C (32°F)
966G and 972G Wheel Loaders Display Modules (Caterpillar Monitoring System)
928G Wheel Loader Seat
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Hydraulic System Oil Filter - Replace
793B Off-Highway Truck Steering System Steering Gear
966G and 972G Wheel Loaders Hydraulic System Oil - Change
793C and 793C XQ Off-Highway Truck Steering System Piston Pump (Steering)
793B Off-Highway Truck Steering System Steering Control Valve
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Engine Oil and Filter - Change
928G Wheel Loader Autoshift Control
12H, 140H, 143H, 160H and 163H Motor Graders Air System and Brakes Service Brakes
12H, 140H and 160H Motor Graders Air System and Brakes Service Brakes
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Fuel System Primary Filter (Water Separator) Element - Replace
561M Pipelayer Transmission Selector and Pressure Control Valve - Power Shift
966G and 972G Wheel Loaders Secondary Steering - If Equipped