561M Pipelayer Track Roller Frame Guides - Inspect Caterpillar


Track Roller Frame Guides - Inspect
`
561M Pipelayer [SEBU7085]
UNDERCARRIAGE
FRAME GP-TRACK ROLLER
561M Pipelayer Track Roller Frame Guides - Inspect

Measure the rotational movement of the front roller frame relative to the rear roller frame.



Illustration 1g00427478
Typical example

  1. Raise the front of the machine. Place a 100 mm (4 inch) block under the outside edge of a track shoe. Place the block near the front track idler. Lower the machine onto the block.


    Illustration 2g00414726
    Typical example

  2. Use a grease pencil to make a mark on the tubular section of the front roller frame. Make a mark on the rear of the roller frame. This mark should correspond with the mark that is on the tubular section.


    Illustration 3g00427479
    Typical example

  3. Raise the front of the machine. Place the block under the inside edge of the same track shoe. Lower the machine onto the block.


    Illustration 4g00414727
    Typical example

  4. Put a mark on the tubular section of the front roller frame. This mark should correspond with the mark on the rear roller frame. Measure the distance between the two marks on the front roller frame.

If the distance between the two marks is greater than 4.5 mm (0.18 inch), inspect the track roller frame guides for wear.

Repeat the entire procedure for the other side of the machine.


NOTICE

Never build up the track roller frame guides with hard-face welding. This will cause serious wear damage to the guide slots in the front track roller frame.




Illustration 5g00039582

If dimension (X) is less than 71.5 mm (2.81 inch), replace the track roller frame guides. Consult your AVSpare dealer for information or for service.

Information System:

834B and 836 Landfill Compactor Throttle Lock Control
834B and 836 Landfill Compactor Starting with Auxiliary Start Receptacle
844 Wheel Dozer Tree or Brush Removal
D9R Track-Type Tractor Standard Torque for Worm Drive Band Hose Clamps
D6R Track-Type Tractor Operation
834B and 836 Landfill Compactor After Starting Engine
CP-433C, CS-431C and CS-433C Paving Compactors Engine Starting with Jump Start Cables
834B and 836 Landfill Compactor Transmission Oil Filter - Replace
834B and 836 Landfill Compactor Rollover Protective Structure (ROPS) - Inspect
834B and 836 Landfill Compactor Transmission Oil - Change
834B and 836 Landfill Compactor Hydraulic System Oil Level - Check
834B and 836 Landfill Compactor Hydraulic System Oil - Change
834B and 836 Landfill Compactor Refill Capacities
834B and 836 Landfill Compactor Caterpillar Reference Material
834B and 836 Landfill Compactor Power Guard Control
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Seat Belt Adjustment
12H, 140H and 160H Motor Graders Hydraulic and Steering System Valve and Linkage Group
12H, 140H and 160H Motor Graders Hydraulic and Steering System Blade Lift Control Valve
D9R Track-Type Tractor Ripping
D9R Track-Type Tractor Adjustable Ripper
120H and 135H Motor Graders Hydraulic and Steering System Drawbar
120H Motor Grader Hydraulic and Steering System Drawbar
12H, 140H and 160H Motor Graders Hydraulic and Steering System Snow Plow/Bulldozer Relief Valve
12H, 140H, 143H, 160H and 163H Motor Graders Hydraulic and Steering System Control Valve (Snow Plow/Dozer Lift)