834B and 836 Landfill Compactor V-Belts - Inspect/Adjust/Replace Caterpillar


V-Belts - Inspect/Adjust/Replace
`
834B and 836 Landfill Compactor [SEBU6696]
BASIC ENGINE
DRIVE GP-FAN
834B and 836 Landfill Compactor V-Belts - Inspect/Adjust/Replace
1.1. Alternator Belt
2.1. Air Conditioner Belt



Illustration 1g00274715

Note: Stop the engine before you check any belts. Open the access cover on the right side of the machine.

Alternator Belt




    Illustration 2g00668379

  1. Inspect the condition of the alternator belts. Use a Kent Moore Company BT-33-72C gauge to check the tension of the alternator belts.

    The tension of a used alternator belt with more than 30 minutes of operation at rated speed should be 400 ± 44 N (110 ± 10 lb). The tension of a new alternator belt with 30 minutes of operation or less at rated speed should be 534 ± 22 N (180 ± 5 lb).

    If the alternator belts require adjustment or replacement, proceed to Step 2.




    Illustration 3g00668395

  1. Loosen mounting bolts (2) and adjusting locknut (3) .

  1. Turn adjusting nut (1) until the correct belt tension is reached. Tighten adjusting locknut (2) to a torque of 150 ± 20 N·m (110 ± 15 lb ft).

  1. Tighten mounting bolts (2) .

  1. Recheck the belt tension. If the tension is incorrect, repeat the adjustment procedure.

Air Conditioner Belt




    Illustration 4g00038527

  1. Inspect the condition of the air conditioner belt. Use a Kent Moore Company BT-33-97 gauge to check the tension of the air conditioner belt.

    The tension of a used air conditioner belt with more than 30 minutes of operation at rated speed should be 400 ± 44 N (160 ± 10 lb). The tension of a new air conditioner belt with 30 minutes of operation or less at rated speed should be 534 ± 44 N (240 ± 10 lb).

    If the air conditioner belt requires adjustment or replacement, proceed to Step 2.




    Illustration 5g00038529

  1. Loosen compressor bracket mounting bolt (1) and adjusting locknut (2) .

  1. Turn adjusting nut (3) until the correct belt tension is reached. Tighten adjusting locknut (2) to a torque of 150 ± 20 N·m (110 ± 15 lb ft).

  1. Tighten compressor bracket mounting bolt (1) .

  1. Recheck the belt tension. If the tension is incorrect, repeat the adjustment procedure.

Information System:

834B and 836 Landfill Compactor Lift Control
834B and 836 Landfill Compactor Air Conditioner - Test
834B and 836 Landfill Compactor Transmission Direction and Speed Control
834B and 836 Landfill Compactor Parking Brake Control
834B and 836 Landfill Compactor Heating and Air Conditioning Control
834B and 836 Landfill Compactor Backup Alarm
834B and 836 Landfill Compactor Light Switches
834B and 836 Landfill Compactor Parking Brake Manual Release
834B and 836 Landfill Compactor Gauges
834B and 836 Landfill Compactor Electronic Monitoring System (EMS)
834B and 836 Landfill Compactor Product Identification Number, Serial Number and EU's CE Plate Locations
834B and 836 Landfill Compactor Model View Illustrations
834B and 836 Landfill Compactor Circuit Breakers - Reset
834B and 836 Landfill Compactor Coolant Conditioner Element - Replace
834B and 836 Landfill Compactor Cab Air Filter - Clean/Replace
834B and 836 Landfill Compactor Differential and Final Drive Oil - Change
834B and 836 Landfill Compactor Ether Starting Aid Cylinder - Replace
834B and 836 Landfill Compactor Engine Oil (High Speed) and Oil Filter - Change - If Equipped
834B and 836 Landfill Compactor Fuel System - Prime
834B and 836 Landfill Compactor Fuel System Secondary Filter - Replace
834B and 836 Landfill Compactor Fuel Tank Cap and Strainer - Clean
834B and 836 Landfill Compactor Fuses - Replace
834B and 836 Landfill Compactor Steering Cylinder Bearings - Lubricate
834B and 836 Landfill Compactor Hydraulic System Oil - Change