CB22, CB24, CB32 and CC24 Utility Compactors Cooling System Water Temperature Regulator - Replace Caterpillar


Cooling System Water Temperature Regulator - Replace
`
CB22, CB24, CB32 and CC24 Utility Compactors [KEBU7540]
COOLING SYSTEM
LINES GP-WATER
CB22, CB24, CB32 and CC24 Utility Compactors Cooling System Water Temperature Regulator - Replace

------ WARNING! ------

At operating temperature, the engine coolant is hot and under pressure.

Steam can cause personal injury.

Check the coolant level only after the engine has been stopped and the fill cap is cool enough to touch with your bare hand.

Remove the fill cap slowly to relieve pressure.

Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to prevent personal injury.


Replace the water temperature regulator on a regular basis in order to reduce the chance of unscheduled downtime and of problems with the cooling system.

The water temperature regulator should be replaced after the cooling system has been cleaned. Replace the water temperature regulator while the cooling system is completely drained. Replace the water temperature regulator while the cooling system coolant is drained to a level below the water temperature regulator housing.


NOTICE

Failure to replace the engine's water temperature regulator on a regularly scheduled basis could cause severe engine damage.


Note: If you are only replacing the water temperature regulator, drain the cooling system coolant to a level that is below the water temperature regulator housing.

  1. Open the engine compartment. Refer to the Operation and Maintenance Manual, "Access Doors and Covers".


    Illustration 1g01416235

  2. Remove the cooling system pressure cap in order to relieve the pressure in the cooling system.


    Illustration 2g01416278

  3. Remove the housing for the water temperature regulator.

  4. Remove the gasket and remove the water temperature regulator.


    NOTICE

    The water temperature regulators may be reused if the water temperature regulators are within test specifications, are not damaged, and do not have excessive buildup of deposits.



    NOTICE

    If the water temperature regulator is installed incorrectly, it will cause the engine to overheat.


  5. Install a new water temperature regulator and install a new gasket.

  6. Install the housing for the water temperature regulator.

  7. Add the cooling system coolant. Maintain the level of the coolant to 1 cm from the bottom of the fill pipe.

  8. Inspect cooling system pressure cap and the gasket for damage. Replace the pressure cap if the pressure cap or the gasket are damaged.

  9. Install the cooling system pressure cap.

  10. Close the engine compartment.

Information System:

CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Motor (Wheel Propel)
CB22, CB24, CB32 and CC24 Utility Compactors Cooling System Coolant Extender (ELC) - Add
CB22, CB24, CB32 and CC24 Utility Compactors Cooling System Coolant (ELC) - Change
CB22, CB24, CB32 and CC24 Utility Compactors Braking System - Test
770 and 772 Off-Highway Trucks Power Train Final Drive - Assemble
770 and 772 Off-Highway Trucks Power Train Final Drive - Disassemble
770 and 772 Off-Highway Trucks Power Train Final Drive - Install
770 and 772 Off-Highway Trucks Power Train Final Drive - Remove
2570C and 2670C Wheel Feller Bunchers Engine Air Filter Secondary Element - Replace
CP54 and CS54 Vibratory Soil Compactors Machine Systems Relief Valve (Main, Vibratory) - Test and Adjust
140M and 150 Motor Grader Piston Pump (Hydraulic Fan) - Remove
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Motor (Drum Propel)
Repair of Cracks in Front Frame Crossmember{7051}
C32 Engine for D11T Track-Type Tractors Cooling Fan Override - Test
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Electrical Schematic (Propel System)
CB22, CB24, CB32 and CC24 Utility Compactors Engine Oil Level - Check
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Hydraulic Schematic (Propel System)
CP54 and CS54 Vibratory Soil Compactors Machine Systems Magnetic Sensor (Vibratory) - Test and Adjust
CS54 and CP54 Vibratory Soil Compactors Fuel System - Prime
140M and 150 Motor Grader Power Train Service Brake (Wheel Spindle) - Disassemble
12M and 140 Motor Graders Power Train Service Brake (Wheel Spindle) - Assemble
CP54 and CS54 Vibratory Soil Compactors Machine Systems Case Drain Flow for Piston Motor (Vibratory) - Test
2007/10/08 A New Main Power Relay and Starter Relay are now used {4493, 7499}
2007/12/31 Correction to Service Magazine , "New Software is Available for the Oil Renewal System" {1349, 7620}