CB22, CB24, CB32 and CC24 Utility Compactors Braking System - Test Caterpillar


Braking System - Test
`

Note: If the machine configuration changes, the parking brakes need to be tested.

Check the area around the machine. Make sure that the machine is clear of personnel and clear of obstacles.

Put the steering frame lock in the UNLOCKED position.

Fasten the seat belt before checking the parking brake.

The following tests are used to determine if the parking brake is functional on a specified grade or a specified slope. These tests are not intended to measure the maximum brake holding effort. Read all of the steps before you perform the following procedure.



Illustration 1g01416207

Position the machine on the incline of the slope, but near the base of the slope in order to check the parking brake. The test position should be 26 percent or a 15 degree slope.

  1. Start the engine. Refer to the Operation and Maintenance Manual, "Engine Starting" for information on starting the engine.

  2. Move the machine into the test position.

  3. Place the throttle control into the LOW IDLE position.

  4. Engage the parking brake.

    The machine should not move under the following conditions.

    • The engine is at low idle.

    • The parking brake is applied.

    • The machine is positioned on the specified slope.

    ------ WARNING! ------

    Personal injury can result if the machine moves while testing.

    If the machine begins to move, release the parking brake and use the propel lever in order to move the machine to a level surface.


  5. Park the machine on a level surface.

  6. Stop the engine.


NOTICE

If the machine moved during the brake test, consult your AVSpare dealer.

The dealer must inspect the brake system and make any necessary repairs before the machine is returned to operation.


Information System:

770 and 772 Off-Highway Trucks Power Train Final Drive - Assemble
770 and 772 Off-Highway Trucks Power Train Final Drive - Disassemble
770 and 772 Off-Highway Trucks Power Train Final Drive - Install
770 and 772 Off-Highway Trucks Power Train Final Drive - Remove
2570C and 2670C Wheel Feller Bunchers Engine Air Filter Secondary Element - Replace
CP54 and CS54 Vibratory Soil Compactors Machine Systems Relief Valve (Main, Vibratory) - Test and Adjust
140M and 150 Motor Grader Piston Pump (Hydraulic Fan) - Remove
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Motor (Drum Propel)
Field Installation of the Traction Control System for the 770, and 772 Off-Highway Trucks{1408, 3288, 4257, 4294, 4801, 4811, 5057, 7610, 7620, 7960}
140M and 150 Motor Grader Secondary Steering Pump and Motor - Install
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Pump (Propel)
120M and 12M Motor Grader Machine Systems Articulation Cylinder - Remove and Install - Left Side
CB22, CB24, CB32 and CC24 Utility Compactors Cooling System Coolant (ELC) - Change
CB22, CB24, CB32 and CC24 Utility Compactors Cooling System Coolant Extender (ELC) - Add
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Motor (Wheel Propel)
CB22, CB24, CB32 and CC24 Utility Compactors Cooling System Water Temperature Regulator - Replace
Repair of Cracks in Front Frame Crossmember{7051}
C32 Engine for D11T Track-Type Tractors Cooling Fan Override - Test
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Electrical Schematic (Propel System)
CB22, CB24, CB32 and CC24 Utility Compactors Engine Oil Level - Check
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Hydraulic Schematic (Propel System)
CP54 and CS54 Vibratory Soil Compactors Machine Systems Magnetic Sensor (Vibratory) - Test and Adjust
CS54 and CP54 Vibratory Soil Compactors Fuel System - Prime
140M and 150 Motor Grader Power Train Service Brake (Wheel Spindle) - Disassemble