CB22, CB24, CB32 and CC24 Utility Compactors Rollover Protective Structure (ROPS) - Foldable Caterpillar


Rollover Protective Structure (ROPS) - Foldable
`
CB22, CB24, CB32 and CC24 Utility Compactors [KEBU7540]
OPERATOR STATION
ROPS/FOPS GP
CB22, CB24, CB32 and CC24 Utility Compactors Rollover Protective Structure (ROPS) - Foldable
1.1. Raise
2.1. Lower


Illustration 1g01414315

If the machine is equipped with a foldable rollover protective structure (ROPS), the ROPS must be in the raised position before you operate the machine. Before the machine is shipped, lower the ROPS in order to provide more clearance during transportation. The ROPS can be folded toward the front of the machine or toward the rear of the machine.



Illustration 2g01356930

Raise

In order to raise the ROPS, perform the following steps:

  1. Raise the ROPS to the full upright position.

  2. Install the front locking pin if the ROPS was folded toward the rear of the machine. Install the rear locking pin if the ROPS was folded toward the front of the machine.

  3. Install cotter pins (2) through locking pins (1). This will lock the locking pins in place.


    Illustration 3g01114409

  4. Tighten locking lever (3).

    Note: In order to tighten the locking lever, perform the following procedure:

    1. Turn the locking lever clockwise. Turn the locking lever by one-half turn.

    2. Raise the locking lever.

    3. Turn the locking lever counterclockwise by one-half turn.

    4. Release the locking lever. This will allow the locking lever to lower.

    5. Repeat step 4.a and step 4.d until the locking lever is tight. Move the locking lever to the full counterclockwise position after the locking lever is tightened.

Lower

In order to lower the ROPS, perform the following steps:

  1. Loosen locking lever (3).

    Note: In order to loosen the locking lever, perform the following procedure:

    1. Raise the locking lever.

    2. Turn the locking lever clockwise by one-half turn.

    3. Release the locking lever. This will allow the locking lever to lower.

    4. Turn the locking lever counterclockwise by one-half turn.

    5. Repeat step 1.a and 1.d until the locking lever is loosened.

  2. Remove the front cotter pin and the front locking pin in order to fold the ROPS toward the rear of the machine. Remove the rear cotter pin and the rear locking pin in order to fold the ROPS toward the front of the machine.

  3. Lower the ROPS.

  4. In order to store locking pins (1), install locking pins (1) into the holes on the ROPS post.

  5. Install cotter pins (2) through locking pins (1). This will lock the locking pins in place.

Information System:

PL1000E Communication ECM Modbus Master
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Case Drain Flow for Piston Motor (Drum Propel) - Test
279C, 289C and 299C Compact Track Loaders Reference Material
The Electronic Priming Pump for Machine Engines will not Prime{1258, 1263}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Piston Ring Groove - Inspect
2007/10/08 A New Main Power Relay and Starter Relay are Now Used {4493, 7499}
2007/10/08 A New Main Power Relay, Starter Relay and Glow Plug Relay are Now Used {1403, 1412, 4493, 7499}
Replacement of the Blower Assembly on Certain Wheel Loaders{7304, 7320}
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Neutral Start Switch - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Axle Propel) - Test and Adjust
2007/10/01 A New Transmission Speed Sensor is Now Available for Series H-Series Motor Graders {3175}
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Drum Propel) - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Case Drain Flow for Piston Motor (Axle Propel) - Test
140M and 150 Motor Graders Engine Supplement Engine Oil Filter and Base - Remove and Install
CB22, CB24, CB32 and CC24 Utility Compactors Shipping the Machine
VIMS Communicator Toolkit Poll Parameters
VIMS Communicator Toolkit Program Description
VIMS Communicator Toolkit Setup
VIMS Communicator Toolkit System Requirements
VIMS Communicator Toolkit Troubleshooting
160M and 160 Motor Grader Machine Systems Control Valve (Brake) - Remove
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Travel Speed - Check
160M and 160 Motor Grader Machine Systems Control Valve (Brake) - Install
VIMS Communicator General Information